manualshive.com logo in svg

S&C PureWave AVC, Инструкция по установке и эксплуатации

Поделиться
Скачать
S&C PureWave AVC Скачать руководство пользователя страница 18

656-500

18

Completing the Installation

1. Depending on the configuration, provide 110-Vac or 208-Vac control

voltage inside the control section to power the fans and controls.
See Figure 14.

2. Close and lock all doors on the PureWave AVC.

3. Wipe down the exterior of the enclosure with a clean, damp cloth.

Refinish any scratches or abrasions with S&C red-oxide primer and
touch-up finish, which are available in aerosol spray cans. See Fig-
ure 15. Order Catalog Number 9999-061 red-oxide primer and Cata-
log Number 9999-080 light gray finish. No other primer or finish is
approved. The area to be touched up should be cleaned to remove
all oil and grease. Sand the area, removing any traces of rust that
may be present. make sure that all edges are feathured before apply-
ing primer.

Figure 15. S&C red-oxide primer and touch-
up finish.

CABLE CONNECTIONS

Figure 14. 110-Vac, 30-A safety switch configuration (left), 208-Vac panel
board for larger, outdoor applications (right).

Ç

 CAUTION

Before walking away. . .

1. Check the interior of the unit for foreign materials, tools, etc.,

which may have been mislaid on bus work or supporting mem-
bers.

2. Make certain that controls are in the desired positions.

3. Make certain that fuses are installed and breakers are in the

proper position.

4. Close and securely latch all doors.

5. Make certain that all temporary grounds have been removed.

6. Padlock all door handles.

Содержание PureWave AVC

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды