background image

- 6 -

Caution!

:

Always turn water OFF before removing the cartridge. Open the handle to relieve
water pressure and ensure that water shut-off has been accomplished.

Kitchen Faucet 

K8792J-BW

PRIOR TO INSTALLATION

Prior to installing new faucet, install the items listed below: 
* Kitchen sink

Shower Flow

 Ordinary Flow

* Drain Line
Important !
* All plumbing is to be installed in accordance with applicable codes and 
   regulations.
* Flush all water lines prior to making connection.

K8792J-BW

- 3 -

Flow

To hot water

To cold water

Stop

C A R T R I D G E   R E P L A C E M E N T  

O P E R A T I O N

5

8

8

7

6

3

2

1

4

1

3

2

4

1. 

Remove the top cap(1) of the handle & loosen the screw(2) with screw driver.

2. 

Remove the lever cover(3) of the handle & loosen the screw(4) with screw driver.

3.

 After removing the lever(5), unscrew the cartridge cover(6) and cartridge

    holder(7).

4.

 Remove an old ceramic cartridge(8) with pliers and replace a new

    ceramic cartridge(8).

5.

 To reassemble, reverse the previous steps.

9-4/5"(250mm)

10-3/5"(270mm)

8-2/5"(213mm)

3-3/10"(85mm)

MAX13-2/5"(341mm)

1/2-14 NPSM

Either ordinary flow or shower flow can be used.

Содержание K8792J-BW








Отзывы: