Fast Track Troubleshooting
Models:
WF209ANW/XAA
Publication # tsWF209 Revision Date 08/13/2010
Quick Test Mode
Note: This test erases all faults and memory
:
To enter press Spin,
Soil, & Power
simultaneously with the power off.
1. All LED’s light up and the washer beeps as it
enters the Quick Test Mode.
2. The unit displays the software version.
3. After the displaying the software version, turn
Jog dial CCW Once, or Twice (showing zeros) on
some units
If EEEE is displayed the PCB ass’y is defective.
Press
Temp Key (press spin to lock door if neces-
sary)
to cycle through the Water Valves circuit test in
this order: Cold Main, Bleach, Cold Main & Bleach for
Fabric Softener, Hot, then off.
Press
Soil Key
to test the motor
Press
Spin
to test Door Lock/Unlock circuit.
Press
Signal Key
to test the Pump
Service Mode:
This mode allows more detailed operation tests and trouble-
shooting, to enter press
Signal & Extra Rinse
simultaneously with the power on.
While in Service Mode the following tests can be performed:
Quick Spin Test =
Delay Start & Spin: This
accelerates
the drum motor from 0 to maximum RPM over a few min-
utes.
Note: Stay with the washer during this test, out of bal-
ance detection is bypassed and the door may not lock.
Press the Start/Pause button during the test to hold its spinning
speed for 10 minutes before going back to Quick Spin Test
Mode.
Cycle Count =
Press the
Signal
button to see how many times
the unit was used
Soft Ware # =
Press the
Soil
button to see the software version
information
Fast Time Down =
Press the
Temp
button to advance to the
next cycle
Fault Code Test =
Press the Spin button to view the stored fault
codes – then turn Dial to view error codes (Push Start/Pause
while the code is displayed to view the number of cycles since
the error occurred)
Peripheral (Main PCB) input Tests
1.
Select Extra Wash. Then turn the Dial
so that the
Heavy
is
turned on. Next, press the Start/Pause Key. The Water
Temperature will be displayed in Fahrenheit.
2.
Select Extra Wash. Then turn the Dial
so that the
White
is
turned on. Next, press the Start/Pause Key. The door status will
be displayed (OP if open, CL if closed).
3.
Select Extra Wash. Then turn the Dial
so that the
Perm.
Press
is turned on. Next, press the Start/Pause Key. The door
lock Switch status will be displayed (UL if unlocked, Lo if
locked).
4.
Select Extra Wash. Then turn the Dial
so that the
Wool
is
turned on. Next, press the Start/Pause Key. The Water
Frequency will be displayed.
IMPORTANT SAFETY NOTICE
–
“For Technicians Only”
This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
Location considerations
Do not install your washer in areas where
water may freeze, since your washer will
always maintain some water in its water valve,
pump, and hose areas. This can cause
damage the belts, the pump, hoses and other
components.
Operating temperature should
be above 60°F/16°C.
EEPROM Clear Check
Power off, Press Delay Start, Signal and Power Key at
the same time. Good = Good Fail = FAiL
All memory will be cleared, including Fault Codes
This should be done when a new Main PCB is
installed
Please Note:
There are
two Versions of this model,
verify you are ordering the
correct parts for the Version
you are servicing.
1
Содержание WF209ANW/XAA
Страница 2: ...WF209 2 ...
