Samsung Verizon SLS-BU102 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 57

Samsung Verizon SLS-BU102 Скачать руководство пользователя страница 54

Chapter 5 Troubleshooting

Verizon 4G LTE Network Extender for Enterprise User Guide VSR 1.2.6 v1.0

47

© Samsung

The following table lists minor alarms. The Network Extender will continue to
function, but it may function with reduced performance.

Table 5. Minor Alarms

Error

Description

Next Step

OVERLOAD

The average CPU load has
exceeded a threshold.

There is a temporary CPU load alert, but
your device is still functioning correctly.
This alert should clear itself. If the alert
persists for a long time, please check the
number of users on the Connected
Devices page and see the capacity
section of the installation guide.

DISK_FULL

Disk usage has exceeded a
threshold.

There is a temporary disk usage alert, but
your device is still functioning correctly.
This alert should clear itself. If the alert
persists, please check the number of
users on the Connected Devices page
and see the capacity section of the
installation guide.

MEMORY_FULL

Memory usage has exceeded
a threshold.

There is a temporary memory usage
alert, but your device is still functioning
correctly. This alert should clear itself. If
the alert persists, please check the
number of users on the Connected
Devices page and see the capacity
section of the installation guide.

PROCESS_DOWN

An application block is
deactivated/terminated.

There is a temporary process alert, but
your device is still functioning correctly.
No action is needed and the alert should
clear itself.

ANTENNA_FAIL

The feeding current to the
antenna side is open/short or
the antenna cable is
dismounted.

Your RF antennas may have problems.
Please ensure that your antennas, and
any extension cables, are correctly
installed as described in the installation
guide.

TOD_MSG_MISSED

The TOD message is not
received from the PTPM.

There is a failure preventing your device
from functioning correctly.

DIGITAL_INPUT_HIGH

Digital input power level is
higher than a threshold.

There is an RF alert, but your device is
still functioning correctly. No action is
needed.

DIGITAL_INPUT_LOW

Digital input power level is
lower than a threshold.

There is an RF alert, but your device is
still functioning correctly. No action is
needed.

VSWR_FAIL

Antenna has a fault or antenna
cable is not correctly
connected.

Your antenna system is not functioning
correctly. Please ensure that your
antennas, and any extension cables, are
correctly installed as described in the
user guide. If your issue persists, please
contact Verizon Wireless Customer Care.

RX_PATH_FAIL

RSSI level is below a
threshold.

There is a RF alert, but your device is still
functioning correctly. No action is
needed.

«
...
52
53
54
55
56
...
»

Содержание Verizon SLS-BU102


























































Отзывы:

Нет отзывов