Samsung SL-X7600GX Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 521

background image

1. Precautions

1.3. ESD precautions

Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
“Electrostatic discharge”. Examples of typical ESDs are: integrated circuits, some field effect transistors, and semiconductor
“chip” components. The techniques outlined below should be followed to help reduce the incidence of component damage
caused by static electricity.

CAUTION

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

1) Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any

electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available
wrist strap device, which should be removed for your personal safety reasons prior to applying power to the unit
under test.

2) After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as

aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.

3) Use only a grounded tip soldering iron to solder or desolder ESDs.

4) Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can

generate electrical charges sufficient to damage ESDs.

5) Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.

6) Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most

replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable
conductive material.

7) Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective

material to the chassis or circuit assembly into which the device will be installed.

8) Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until

completely plugged or soldered into the circuit.

9) Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing together

of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to damage an ESD.

1-6

Copyright© 1995-2013 SAMSUNG. All rights reserved.

«
...
14
15
16
17
18
...
»

Содержание SL-X7600GX










































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL-X7600GX

Бренд: Sharp Страницы: 5

Бренд: Sharp Страницы: 26

Бренд: Sharp Страницы: 52

Бренд: Sharp Страницы: 56

Бренд: Sharp Страницы: 84

Бренд: Sharp Страницы: 80

Бренд: Sharp Страницы: 80

Бренд: Sharp Страницы: 84

Бренд: Sharp Страницы: 76

Бренд: Sharp Страницы: 88

Бренд: Sharp Страницы: 82

Бренд: Sharp Страницы: 92

Бренд: Sharp Страницы: 158

Бренд: Sharp Страницы: 168

Бренд: Sharp Страницы: 178

Бренд: Sharp Страницы: 178

Бренд: Sharp Страницы: 184

Бренд: Sharp Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды