Samsung SCX-6545N Series Скачать руководство пользователя страница 219

Страница: 219 / 392

Alignment & Troubleshooting

Service Manual

4-95

Samsung Electronics

Message

Description

Suggested solutions

Fuser error: #02-002.
Please turn off then on

1. At warm up, the temperature

keep up the lower temperature for
regular time.

2. At warm up, after temperature

checking time, more than regular

temperature and for more 10 sec.

3. At standby or sleep, more than

Top temp and for a few minutes.

4. At power save mode, the

temperature keep up the constant
for regular time.

Replace Fuser or Fuser control board or
Engine controller.

Fuser unit is not installed
correctly. Install it.

The fuser unit is not installed or
correctly

Install the fuser unit.

Hard disk drive error:
#10-003. Please turn Off
then On

Hard disk has some problems.

1. Turn off the power. Reconnect the Hard

disk. And check the error message after
turn on the power.

2. If the problem persists, replace the Hard

disk.

3. If the problem persists, replace the main

board.

Imaging unit error: #06-
013~16. Please turn off
then on

Imaging unit error

1. Check the T/C sensor Harness connection.

2. Check the T/C sensor output wave.

3. Check the Engine B/D TC Sensor ADC

Imaging unit is not
installed. Install it

The imaging unit is not tinstalled,

or the CRUM in the cartridge is not
connected.

Replace the imaging unit.

Imaging unit is worn.
Replace with new one

The imaging unit is at the end of its
life.

Replace the imaging unit.

LSU error: #04-000.
Please turn off then on

LSU motor does not operate.

After checking the LSU motor rotation noise,

check the motor signal.

LSU error: #04-001.
Please turn off then on

After LD on, the Laser beam detect

signal is not occurred or irregular.

1. Check the Beam Detecht signal. If there is

a BD signal, replace the Main board. If or
not, check the LD contol signal.

2. Check the LD Power is normal.

3. If it is normal, check the light receving part.

LSU error: #04-002.
Please turn off then on

LSU motor does not operate or the
drive signal is abnormal.

After checking the LSU motor rotation noise,

check the motor signal.

Memory failure: #10-001.
Please turn off then on

At system booting, the memory is not

read.

Replace the memory

Motor does not operate:
#03-006. Please turn off
then on

After Black OPC BLDC motor is

operated, the ready signal is not

occurred within 1 sec.

Take out the toner cartridge and shake it
horizontally. And re-install it.

Содержание SCX-6545N Series









































































































































































































































































































































































































Результаты поиска

Содержание SCX-6545N Series

Отзывы:

Похожие инструкции для SCX-6545N Series

Бренды по названию

Популярные бренды

Samsung SCX-6545N Series, Руководство по обслуживанию

Результаты поиска

Содержание SCX-6545N Series

Отзывы:

Похожие инструкции для SCX-6545N Series

Бренды по названию

Популярные бренды