Samsung SCX-6545N Series Скачать руководство пользователя страница 223

Страница: 223 / 392

Alignment & Troubleshooting

Service Manual

4-99

Samsung Electronics

Message

Description

Suggested solutions

Scanner locking switch
is locked or another
problem occurred.

The CCD lock has been locked.

1. Unlock the CCD Lock
2. Check the CCDM. Is is moving when

scanning. Check the FFC cable. If there is

defective, change it.

3. If the problem persists after removing the

FFC cable, replace the DADF board.

4. Check the Scan-motor. If there is

defective, change it.

System error: #02-000.
Please turn off then on

1. At warm up, the temperature is

less than reference temperature
for 20 sec.

2. Abnormal ADC has occurred.
3. ZeroCross Signal detect error has

occurred.

1. In case of meaning 1, replace the Fuser

unit.

2. In case of meaning 3, replace the Engine

contol board or Fuser control board or
SMPS.

Staple cartridge is empty.
Replace it.

Stapler is run out.

Order Staple cartridge.

System error: #02-003.
Please turn off then on

The communication error of the
MEGA88 Micom

1. Open the side cover and close it.
2. Check the envelope pressing device.

System error: #10-004.
Please turn off then on

UI error

1. check the UI connector.

2. If the problem persists, replace the OPE

board.

3. If ther problem persists, replace the maina

board.

This IP address conflicts

with an IP address
already in use. Check it

The IP address is used in other place
elsewhere.

Check the IP address or obtain a new IP
address.

Toner cartridge is not
compatible. Check user's
guide

The toner cartridge you have
installed is not for your machine.

Replace the toner cartridge.

Toner cartridge is not
installed. Install it.

The toner cartridge is not installed
or the CRUM in the cartridege is not
properly connected.

Check the connection between the CRUM
connector of the toner cartridge and Set.

Toner cartridge is worn.
Replace with new one

The color toner cartridge has run out.
The machine stops printing.

Replace the toner cartridge.

Toner cartridge: #06-
006~7. Please turn off
then on

Toner Cartridge Error

Replace the toner cartridge.

Toner is empty. Replace
toner cartridge

The lifespan of the color toner
cartridge which the arrow indicates is
reached.

Replace the toner cartridge.

Toner is low. Order new
toner cartridge

Toner Cartridge is almost empty.

Replace the toner cartridge.

Содержание SCX-6545N Series









































































































































































































































































































































































































Результаты поиска

Содержание SCX-6545N Series

Отзывы:

Бренды по названию

Популярные бренды

Samsung SCX-6545N Series, Руководство по обслуживанию

Результаты поиска

Содержание SCX-6545N Series

Отзывы:

Бренды по названию

Популярные бренды