background image

Making Calls

Receiving Calls

Basic Operation

Setting up your terminal

LED indications are described in the following table:

Sound indications are described in following table:

LED

Color

Condition

Meaning

Power

Off

No Power is being supplied the terminal.

RED

On

Normal operation.

RED

On

No service condition. In this case, contact 
your dealer.

RSSI

ORANGE

On

Voice through the line is not clear but a call 
is available.

Blinking

Incoming call

GREEN

On

Best service condition.

Blinking

Incoming call

Off

Normal operation without any voice mail

Voice

message.

Mail

You have voice mail message.

GREEN

On

Contact your service provider to activate
Message Service.

Type

Normal dial tone

No Service tone

Outgoing call 
restriction tone

Voice mail tone

Condition

20sec on; 
300msec off

1.5sec on;
800 msec off

800  msec on; 
200 msec off

three times (100msec
on;100msec off)

Meaning

The FWT is in-service with
adequate receive signal.

FWT is not capable of
making or receiving calls.

FWT is not  capable of
making calls but is 
capable of receiving calls.

You have voice mail 
message.

SCW-R500  1/9/99 12:06 PM  Page 10

Содержание SCW-510














Отзывы: