SYSTEM CONTROLLER
User’s Manual
22
SYSTEM CONTROLLER
User’s Manual
21
3. SWING
This menu is for setting the camera to alternate between two assigned locations
horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only
possible in the SPD series. In case of products by other manufacturers, the setting has to be
done by the OSD menu of the camera. See the camera manual for more information.
4-2. GROUP Operation
3-1. SWING Setup
At the [PTZ SETUP 1 ] ] menu, press the 2 button
(see p.19).
Press the 1 or 2 button to select a horizontal (pan) or
vertical (tilt) cycle.
Set starting point, ending point, movement speed,
and stop time.
- /
button: Moves between items.
- 1ST
: Starting point. Can be set for Preset 1 ~ 64.
- 2ND : Ending point. Can be set for Preset 1 ~ 64.
- SPEED : Movement speed. Can be set for 1 ~ 64 (see p.44).
- STOP : Stop time at the starting point and ending point. Can be set to 1 ~ 99 (seconds).
Press the ENTER button to finish the setup (takes 2 or 3 seconds to finish).
• The Swing function cannot be set if an unassigned number or a number outside the
selectable range is entered.
• Over 2 PRESET locations have to be set before setting SWING.
At the [PTZ SETUP 1 ] menu, press the 3 button
(see p.19).
Enter a Group number.
• Any number between 1 and 6 can be selected.
Set each location's Preset ID, area movement speed,
and stop time.
- /
button: Moves between items.
- NO
: Setup sequence. Up to 64 can be selected.
- PRESET : Camera Preset ID for assigned location.
- SPEED : Area movement speed. Can be set from 1 ~ 64 (see p.44).
1~128(SPD-3300/3000/2300)
- STOP
: Stop time at the starting point and ending point. Can be set to 1 ~ 99 (seconds).
Press the ENTER button to move to the setup page for the next location.
Press the Group button to finish the Group Setup.
• The Group function cannot be set if an unassigned number or a number outside the
selectable range is entered.
• Over 2 PRESET locations have to be set before setting GROUP.
At the initial screen, press the Group button.
Press the Group button to execute the operation.
The Group function is performed.
• AUTO-SEQ and SCAN functions are performed when the
GROUP button is pressed (for PANASONIC(WV-CS854A)
and SAMSUNG ELECTRONICS (SCC-641/643 only).
SWING SETUP
CAM ID:
5
SPD
1:PAN SET
2:TILT SET
Press Numeric Key
4. GROUP
This menu is for setting repeated sequential surveillance of assigned locations with
assigned speed and intervals. Setting the GROUP SETUP menu by controllers is only
available for an SPD series. In case of products by other manufacturers, the setting has to
be done by the OSD menu of the camera. See the camera manual for more information.
4-1. GROUP Setup
GROUP SETUP
CAM ID:
5
SPD
GROUP SET NUM? <1-6>
Press Numeric Key
GROUP SETUP
NO PRESET SPEED STOP
01
0
00
00
Enter:Next
GROUP:Set
PTZ CONTROL SYSTEM
CAM ID:
5
SPD
GROUP RUN NUM? <1-6>
Press Numeric Key
3-2. SWING Operation
At the initial screen, press the Swing button.
Press the 1 and 2 buttons to perform the Swing function.
- 1 button: Performs the horizontal cycle (pan).
- 2 button: Performs the vertical cycle (tilt).
• Move the joystick or press a controller button during the Swing operation to stop the operation.
• AUTO-PAN is performed automatically when the SWING button of PANASONIC(WV-
CS854A) and SAMSUNG ELECTRONICS (SCC-641/643) cameras is pressed.
PTZ CONTROL SYSTEM
CAM ID:
5
SPD
1:PAN
2:TILT
Press Numeric Key
SWING SETUP
IST
2ND SPEED STOP
00
00
00
00
Enter:Swing Set
PTZ Mode
PTZ Mode
