Samsung RVXMHF040ESeries, Руководство по установке

Страница: 15 / 34

E-
15
EN
G
LI
SH
Electrical Connections (Continued)

Make a knockout hole by driving in a nail.

After making a knockout hole, apply rust resisting paint around
the hole.

When installing the cables through the knockout hole, remove all
burrs and protect them with the protection tape.
CAUTION

Be sure to run the power supply cable and the communication cable through electrical conduit
as seen in the picture.

Install the communication cable, indoor power cable and the main power cable in the cable tube.

Secure the cable tube to the outdoor knockout using the CD connector and bushing.

Arrange the cables as shown in the picture.

The diameter of the 6 knock-out holes is Ø 27.8 mm.
Power Wiring and Communication Wiring Configuration
3 phase 4 wires (380-415V~)
3 phase 380-415V~
Earth
Communication cable
between indoor and
outdoor units

Connect the power cable of the outdoor unit after checking that L1-L2-L3-N(3 phase 4 wire) is properly connected.
(If 380V power cable is connected to N phase, PCB or other components may be damaged.)

The communication cable between indoor and outdoor units has no polarity.

Secure the cables using the clamp of the electrical component box of the outdoor unit.
Communication cable
Power cable for indoor units
Main power cable
(Inside)
(Outside)

You should connect the power cable into the power cable terminal and fasten it with a
clamp.

The unbalanced power must be maintained within 2% of supply rating.
- If the power is unbalanced greatly it may shorten the life of the condenser.
If the unbalanced power is exceeded over 4% of supply rating, the indoor unit is
protected, stopped and the error mode indicates.

To protect the product from water and possible shock, you should keep the power cable
and the connection cord of the indoor and outdoor units in the iron pipe.

Connect the power cable to the auxiliary circuit breaker. An all pole disconnection
from the power supply must be incorporated in the fixed wiring(≥3mm).

Must keep the cable in a protection tube.

Keep distances of 50mm or more between power cable and communication cable.

Power cable should be used within maximum length limitation.

Each indoor unit power should be supplied between maximum and minimum values.

The power cable is not supplied with the air conditioner.

For the power cable, use the grade H07RN-F or H05RN-F materials.
Outdoor unit
Model
Power Supply
3 Phase 1 Phase
Power
Supply(V)
Max/
Min(V)
MCCB/
ELB
Power
cable
Max
Length
Power
Supply(V)
Max/
Min(V)
MCCB/
ELB
Power
cable
Max
Length
RVXMHF040EA
RVXMHF050EA
- - - - -
220-
240V~/
50Hz
242/198 30A 5.5 mm 2 18m
RVXMHF050GA
380-
415V~/
50Hz
418/342
16A 2.0mm 2 18m
220-
240V~/
50Hz
242/198
16A
2.0 mm 2 18m
RVXMHF060GA 20A 3.5mm 2 18m 20A
Specification of electronic wire of the outdoor unit
Power Supply (1 Phase)
Earth Cable
Communication
cable
Power Supply Max/Min(V) Power cable Max length
220-240V~/50Hz 242/198 2.0mm 2
Decided by power drop
among indoor units
2.0~5.5mm 2 0.75~1.25mm 2
Specification of electronic wire of the indoor unit

coef: Use approximately 1.55

L
k
: Distance between each unit[m], A
k
: Thickness of power cable[mm
2
]
i
k
: Running current of each unit[A]
∑ (
Coef ×35.6×L
k
×i
k
) <20[V]
1000 ×A
k
n
k=1

Select the thickness and length of power cable for total drop of electric pressure to be less than
10%(On 220V lnput voltage basis).
RVXMHF04E0A_E_IM_24820.indd 15 2006-02-01 ¿ÀÈÄ 5:02:25