14_
setting up
Compression
Nut (1/4”)
(Assembled)
Ferrule
(Not supplied)
Plastic Tubing
(Assembled)
Compression
Fitting
(Assembled)
Molded
end(Bulb)
Compression
nut (B) (1/4”)
(Not supplied)
or
Copper tubing
(Not supplied)
Plastic tubing (B)
(Not supplied)
Household water supply line
Refrigerator
1.
Connect the household water line to the
assembled compression fitting.
- If you are using copper tubing, slip the
compression nut (
B
) (not supplied) and
ferrule (not supplied) on the copper tubing (not
supplied) as shown.
- If you are using plastic tubing (
B
) , insert the
molded end (Bulb) of the plastic tubing (
B
) into
the compression fitting.
Do not use without the molded end (Bulb)
of the plastic tubing (
B
).
2.
Tighten the compression nut (
B
) onto the
compression fitting.
Do not over-tighten the compression nut (
B
).
3.
Turn the water on and check for any leakage.
If you find water drops or leakage in the
connection areas, turn off the main water
supply. Check the connections and, if
necessary, tighten.
4.
Flush 1 gallon of water through the filter
before drinking or using the water from the
refrigerator. (Flush approximately 6 minutes.)
To flush, press a large glass or cup against the
water dispenser lever. Fill the glass, empty it
into the kitchen sink after it is filled, and then
repeat.
5.
After you turn on the refrigerator, let the ice
maker make ice for 1 to 2 days. Over that
period of time, throw out the first 1 or 2
CAUTION
buckets of ice the freezer makes to ensure all
impurities have been removed from the water
line.
• Only connect the water line to a
drinkable water source.
• If you have to repair or disassemble the water
line, cut off 1/4” of the plastic tubing to make
sure you get a snug, leak-free connection.
• You can test the water line quickly using
a paper cup. Under normal conditions,
the water dispenser can fill a 5.75 oz.
(170 cc) cup in about 10 seconds.
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
1.
Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
2.
Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
3.
Set the Temperature control to the coldest
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
4.
After you plug the refrigerator in, it will
take a few hours to reach the appropriate
temperature. You can store food and drinks
in the refrigerator after the temperature is
sufficiently cool.
In the event of a power failure, call the local office
of your Electricity Company and ask how long it is
going to last.
- Most power failures that are corrected in an
hour or two will not affect your refrigerator
temperatures. However, you should minimize
the number of door openings while the
power is off.
- But Should the power failure last more than
24hours, remove all frozen food.
DA68-02601A-16.indb 14
2018. 10. 8. 오후 4:32
Содержание RF263TEAESG/AA
Страница 92: ...mémo DA68 02601A 16 indb 30 2018 10 8 오후 4 33 ...
Страница 93: ...mémo DA68 02601A 16 indb 31 2018 10 8 오후 4 33 ...
