Samsung MXD-K025AN Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 40

Samsung MXD-K025AN Скачать руководство пользователя страница 36

35

AHU-KIT Installation Check

1) Ensure that Control-KIT is correctly installed.

   • You can choose the built-in type or auxillary type depending on installation environment.
  • Ensure that the Control-KIT cables are correctly connected.
  •  Control-KIT should be fireproofed and avoid direct sunlight upon installation.

(Especially for individual type)

• Avoid installing the unit in a location exposed to direct sunlight or rain.
• Do not install the Control-KIT in or on the outdoor unit.

2) Ensure that EEV-KIT is correctly installed.

   • Ensure that EEV-KIT can be installed inside or outside, but do not install the EEV-KIT in residential areas.
    •  When EEV-KIT is installed separately outside of the AHU, insulate the pipe to prevent the dew condensate.
   • Ensure that IN/OUT pipes are correctly connected.
    • Ensure that the body of EEV-KIT is installed in level.
   •  Make sure that EEV-KIT is installed where condensation can be drained well.
   •  Do not install the EEV-KIT in or on the outdoor unit.

3) Ensure that IN/OUT sensor is correctly attached.

• IN sensor should be attached after the distributor, on the coldest part of the heat exchanger piping.

Ensure that the sensor is insulated.

• OUT sensor should be installed approximately 200mm behind the header of AHU heat exchanger.

4) Ensure that Disch. sensor is correctly attached. (Optional)

• Disch. sensor should be located after heat exchanger (over 1m)
• Detail explanation of Disch. Temperature setting is on wired remote controller manual.

(Installation manual, service mode)

• When using Disch. temperature control, change the product option code (01 series) SEG 21 “1”.

AFTER INSTALLATION

NASA PJT_AHU Kit_MXD-K@@@AN Series_EN_03711A(1).indd 35

2013-01-11 오후 3:20:36

«
...
34
35
36
37
38
...
»

Содержание MXD-K025AN









































Отзывы:

Нет отзывов