Samsung Mobile WiMAX Outdoor RAS SPI-2331 Скачать руководство пользователя страница 39

Страница: 39 / 96

CHAPTER 3. Outdoor SPI-2331 Architecture

3-6

Downlink (Tx) Signal Processing

As for the downlink signal, the ULRB performs bandpass filtering of baseband I/Q signal

received from the ULDB and converts the signal into the analog signal through Digital to

Analog Conversion(DAC).

The converted analog signal goes through frequency up-conversion to RF band signal, and

the signal is transferred to power amplifier. The power amplifier amplifies the received RF

band signal and sends it to a filter.

The filter filters out unnecessary frequency components from the received RF signal and

sends out the RF signal through the antenna. The power of the RF transmission signal per

Tx path at the RF output port is 100 mW.

Uplink (Rx) Signal Processing

Out-of-band spurious wave of RF signal received from the antenna is suppressed through

front end analog filter. This signal is low noise amplified in Low Noise Amplifier(LNA),

and it is frequency down converted to the analog signal.

The converted analog signal is converted to the digital baseband signal through Analog to

Digital Conversion(ADC), and it is transferred to ULDB.

TDD Operation

The ULRB has a TDD switch and it switches the sending/receiving path by receiving a

TDD signal from the ULDB to help the outdoor SPI-2331 run as a TDD system.

The TDD switch connects with the transmission path in the DL section and provides a

transmission path for downlink signals amplified in the power amplifier. The TDD switch

connects with the reception path in the UL section and provides a reception path for uplink

signals from the MS.

Содержание Mobile WiMAX Outdoor RAS SPI-2331

































































































Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды

Samsung Mobile WiMAX Outdoor RAS SPI-2331, Описание системы

Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды