Samsung Mobile WiMAX Outdoor RAS SPI-2331 Скачать руководство пользователя страница 38

Страница: 38 / 96

Mobile WiMAX Outdoor RAS SPI-2331 System Description/Ed.02

3-5

3.2.2 ULRB

The ULRB is the integrated RF board that carries out the transceiver function, power

amplifier function, TDD switch function, filter function, and the Low Noise Amplifier

(LNA) function.

Figure 3.2 ULRB Block Diagram of Outdoor SPI-2331

The main functions of ULRB are as follows:

High-power amplification of RF transmission signal

Interfacing with ULDB in digital baseband I/Q(LVTTL) signal

Upconversion/downconversion of frequency

Rx/Tx RF signal from/to an antenna

Suppression of out-of-band spurious wave emitted from RF Rx/Tx signal

Low noise amplification of band-pass filtered RF Rx signal

TDD switching function for RF Tx/Rx path

Automatic Gain Control(AGC) for the received RF signal and Received Signal

Strength Indicator(RSSI) support

ULRB

Filter

RF Ant.

TDD Switch

PA LNA

Up/Down Converter

ULDB

TDD

RF(Tx/Rx)

RF(Tx)

RF(Rx)

RF(Tx)

RF(Rx)

Baseband I/Q

(LVTTL)

Содержание Mobile WiMAX Outdoor RAS SPI-2331

































































































Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды

Samsung Mobile WiMAX Outdoor RAS SPI-2331, Описание системы

Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды