Samsung Mobile WiMAX Outdoor RAS SPI-2331 Скачать руководство пользователя страница 29

Страница: 29 / 96

CHAPTER 2. Overview of Outdoor SPI-2331

2-12

Environmental Condition

The table below lists the environmental conditions and related standards such as operational

temperature and humidity.

Category

Range

Applied Standard

Temperature Condition

-40~50

C(-40~122

GR-487-CORE Sec. 3.26

Humidity Condition

5~95%

However, the vapor content for air

of 1

kg should not exceed 0.024

kg.

GR-487-CORE Sec.3.34.2

Altitude -60~1,800

m(-197~6,000

ft) GR-63-CORE

Sec.4.1.3

Earthquake Zone

GR-63-CORE Sec.4.4.1

Vibration Commercial

Transportation Curve 2

GR-63-CORE Sec.4.4.4

Noise(sound pressure

level)

Under 65

dBA in distance of

1.5

m(5

ft) and height of 1.0

m(3

ft).

GR-487-CORE Sec.3.29

Electromagnetic

Wave(EMI)

Standard satisfied

FCC Title47 Part 15 Class B

GR-1089-CORE Sec. 3.2

US Federal Regulation

Standard satisfied

FCC Title47 Part27

a) The standards of temperature/humidity conditions are based on the value on the position where is

400

mm(15.8

in) away from the front of the system and in the height of 1.5

m(59

in) on the bottom.

GPSR Specification

The table below lists the GPS Receiver(GPSR) characteristics of Outdoor SPI-2331.

Category

Description

Received Signal from GPS

1PPS, ToD

Reference signal

8 kHz

Accuracy/Stability 0.01

ppm

Holdover time

24 hr

RF Specification

The table below lists the RF characteristics of the outdoor SPI-2331.

Category

Description

Tx Output Power

200mW @avg power(MIMO) per carrier/sector

Tx Constellation error

802.16e standard is observed.

RX Sensitivity

802.16e standard is observed.

Содержание Mobile WiMAX Outdoor RAS SPI-2331

































































































Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды

Samsung Mobile WiMAX Outdoor RAS SPI-2331, Описание системы

Результаты поиска

Содержание Mobile WiMAX Outdoor RAS SPI-2331

Отзывы:

Похожие инструкции для Mobile WiMAX Outdoor RAS SPI-2331

Бренды по названию

Популярные бренды