Samsung iPolis SNB-7002 Скачать руководство пользователя страница 23

Страница: 23 / 158

English

_23

●

OVER

VIEW

Components

Item

Description

Network Port

Used to connect the PoE or Ethernet cable for network connection.

Alarm I/O Port

ALARM IN

Used to connect the alarm input signal.

ALARM OUT

Used to connect the alarm output signal.

GND

Used for earth-grounding.

Test Monitor Out

Output port for test monitoring the video output. Use the test monitor cable
to connect to a mobile display and check the test video.

Reset Button

The button restores all camera settings to the factory default.
Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that

DHCP can be enabled. If there is no DHCP server in the network, you

must run the IP Installer program to change the basic network settings

such as IP address, Subnet mask, Gateway, etc., before you can

connect to the network.

Содержание iPolis SNB-7002































































































































































Результаты поиска

Содержание iPolis SNB-7002

Отзывы:

Похожие инструкции для iPolis SNB-7002

Бренды по названию

Популярные бренды

Samsung iPolis SNB-7002, Руководство пользователя

Результаты поиска

Содержание iPolis SNB-7002

Отзывы:

Похожие инструкции для iPolis SNB-7002

Бренды по названию

Популярные бренды