Samsung iPolis SNB-7002 Скачать руководство пользователя страница 48

Страница: 48 / 158

installation & connection

48_

installation & connection

Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of
the amplifier that the microphone is connected to.

Connect the AUDIO OUT port of the camera with the speaker or LINE IN port of the
amplifier that the speaker is connected to.

Check the specifications for audio input.

• Audio Codec

G.711 PCM. μ-law 64kbps 8kHz / G.726 (16Kbps, 24Kbps, 32Kbps, 40Kbps)
sampling

• Full duplex Audio

• Audio in

Used for mono signal line input (Max.2.4 Vpp)

• Audio out

Used for mono signal line output (Max.2.4 Vpp)

• Line out impedance

600

Connecting to the I/O port box (SNB-7002)

Connect the Alarm I/O signal to the corresponding port of the rear port box.

•

ALARM IN : Used to connect the alarm input signal.

•

ALARM OUT : Used to connect the alarm output signal.

•

GND : Used for earth-grounding.

Содержание iPolis SNB-7002































































































































































Результаты поиска

Содержание iPolis SNB-7002

Отзывы:

Похожие инструкции для iPolis SNB-7002

Бренды по названию

Популярные бренды

Samsung iPolis SNB-7002, Руководство пользователя

Результаты поиска

Содержание iPolis SNB-7002

Отзывы:

Похожие инструкции для iPolis SNB-7002

Бренды по названию

Популярные бренды