Samsung HHSM-G500005-1 Скачать руководство пользователя страница 8

Страница: 8 / 90

www.jouleuk.co.uk | www.joule.ie

MUST BE COMPLETED AND

THEN REGISTERED ONLINE

TO COMPLETE WARRANTY

Heat Pump

Installation Checklist

Please register your product online

Homeowner

Name
Address

Contact Tel.

Contact Email

Installer

Name
Address

Contact Tel.

Contact Email

Installer’s Signature

Print Name

Date

Heat Pump must be commissioned within 30 days of installation in order to avail of warrenty regis-

tration. If it is found that your system cannot be commissioned due to inadequate installation, the

client will have 2 weeks to get issues rectified and recommissioned to avail of warranty registration.

Charges may apply if a second call out is required by a Joule representative.

Содержание HHSM-G500005-1



























































































Результаты поиска

Содержание HHSM-G500005-1

Отзывы:

Похожие инструкции для HHSM-G500005-1

Бренды по названию

Популярные бренды

Samsung HHSM-G500005-1, Руководство по установке

Результаты поиска

Содержание HHSM-G500005-1

Отзывы:

Похожие инструкции для HHSM-G500005-1

Бренды по названию

Популярные бренды