Samsung DCS Скачать руководство пользователя страница 190

Страница: 190 / 410

SAMSUNG

MMC PROGRAMS

COMBINED SYSTEMS PROGRAMMING MANUAL

FEBRUARY 2004

MMC 501 (Page 6 of 6)

PAGE TIME OUT:

Controls the duration of a page announcement.

PAGE TONE:

Controls the duration of tone burst heard over the page prior to the page announce-

ment.

PARK RECALL:

Controls the period of time a call is parked before recalling to the call park originator.

PC-MMC LOCK:

Monitors PCMMC activity, drops the link if no action is created by PCMMC and re-

turns the system to secure program status.

PERI UCD REPORT:

Controls the interval between periodic UCD reports being output to the applica-

ble port.

POWER DOWN:

Sets the duration of disconnect signal for VM/AA ports.

RECALL DISCONNECT:

The time an attendant recall rings before being disconnected. See

ATT Re-

call

timer

RECALL WAIT:

This is the time any recall (hold or transfer) continues to recall at your station before

it recalls to the operator.

SMDR START/DP (DIAL PULSE (ROTARY)):

This grace period timer starts SMDR recording for ro-

tary dialling. This timer also controls the LCD duration timer on the keysets. The duration time dis-

played and the SMDR time duration will be the same.

SMDR START/DTMF:

This grace period timer starts SMDR recording for touchtone dialling. This

timer also controls the LCD duration timer on the keysets. The duration time displayed and the SMDR

time duration will be the same.

ROUTE OPTIMISE:

When a call is made via Q-SIG signalling, route optimisation is activated after this

time.

SYS HOLD RECALL:

Determines the time calls can be left on hold before recalling the holding sta-

tion. Setting timer to 000 means no recalling will take place.

TRANSFER RECALL:

Determines the time that transferred calls ring before recalling. See

Recall

Wait

timer

TSW CONN. DELAY

On external call forward or tandem working, the time before the forward desti-

nation is connected to the external call. If this timer is very short, the caller hears ringback tone, dial

tone and ringback tone again.

UCDS AUDIO ALARM:

Determines how long the longest waiting call can be held before the system

gives an audio alarm to the UCD supervisor.

UCDS VISUAL ALARM:

Determines how long the longest waiting call can be held before the system

gives a visual alarm to the UCD supervisor.

VMS UCD MSG

: Not used in UK/EU.

VOICE DIAL DELAY:

Monitors the duration of the interaction between the main software and the

Voice Dialler card. If there is no response from the card within this time, the system decides that voice

dialling has failed (

DCS500 and OS500 systems only).

VOIP RE-ROUTE:

Time allowed for the system to wait for a response to a setup message over the

VoIP network before it goes to the next route.

Содержание DCS



























































































































































































































































































































































































































Результаты поиска

Содержание DCS

Отзывы:

Похожие инструкции для DCS

Бренды по названию

Популярные бренды

Samsung DCS, Руководство по программированию

Результаты поиска

Содержание DCS

Отзывы:

Похожие инструкции для DCS

Бренды по названию

Популярные бренды