manualshive.com logo in svg

Samplex Europe SEC-1245E, Руководство пользователя

Поделиться
Скачать
Samplex Europe SEC-1245E Скачать руководство пользователя страница 23

The temperature sensor comes with 5 Metre cable. It has a plug (17) on one end. Connect this plug 

into the jack marked TS (12) on the rear panel of the charger. The other end has the temperature sen-

sor  element  (16).  Mount  this  temperature  sensor  element  flush  with  the  top  surface  of  the  battery  for  pro-

per heat transfer. When the temperature sensor is connected, the voltages during Stage 2 and Stage 3 

are  automatically  adjusted  as  per  the  temperature  of  the  battery  and  the  above  temperature  coefficient.

REMOTE PANEL - MODEL NO. 900-RC

An optional wired Remote Panel Model No. 900-RC (15) can be ordered. It comes with 10

metres of flat ribbon cable (14) that has 8 position modular male connector on either end.

The Remote Panel (15) can be used to switch on / switch off the charger and also monitor 

the charging status of the charger from a remote location.

CONTROLS AND INDICATIONS

The Remote Panel has the following controls / indications:

• Keypad switch for switching on and switching off

• Red LED under “I Phase”

• Yellow LED under “Uo Phase” *

• Green LED under “U Phase”

• Green LED under “Power”

Note:

When “ Loaded Battery” application is selected (see pages 16 & 17), this will

indicate the Float stage (“U” Phase) as in this application, the Boost stage

voltage (“Uo” Phase) is the same as the Float stage voltage (“U” Phase).

CONNECTION

To  connect  the  Remote  Panel  to the charger, insert one connector of the flat ribbon cable 

(14) into the modular jack on the Remote Panel (15) and the other connector to the modular 

jack (6) on the charger.

OPERATION

The charger should be first switched on with the help of the  AC input power on / off switch

(9) located on rear panel of the charger.

The charger can now be switched on and off with the help of the keypad switch on the

Remote Panel (15).

INDICATIONS

Whenever the charger is switched on, the Green LED “Power” will be lighted. The other

LEDs indicate the charging status as follows:

• Red LED “I Phase” is lighted  – Indicates that charger is in Stage 1 - ConstantCurrent,

Bulk Charge Mode (“I” Phase) and is delivering 45 A to 36 A (SEC- 1245E), 60 A to

48 A (SEC-1260E), 80 A to 64 A (SEC-1280E), 25A to 20 A (SEC-2425E)

or 40 A to 32 A (SEC-2440E)

Page 22

Содержание SEC-1245E








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды