background image

SECTION 7  |   

General Information on Lead  

Acid Batteries

22

TABLE 7.4  STATE OF CHARGE VERSUS STANDING VOLTAGE

Percentage of

Full Charge

Standing Voltage of 

Individual Cells

Standing Voltage of

12V Battery

Standing Voltage of

24V Battery

100%

2.105V

12.63V

25.26V

90%

2.10V

12.6V

25.20V

80%

2.08V

12.5V

25.00V

70%

2.05V

12.3V

24.60V

60%

2.03V

12.2V

24.40V

50%

2.02V

12.1V

24.20V

30%

1.97V

11.8V

23.60V

20%

1.95V

11.7V

23.40V

10%

1.93V

11.6V

23.20V

0%

= / < 1.93V

= / < 11.6V

= / < 23.20V

Check the individual cell voltages / specific gravity. If the inter cell voltage difference 
is more than a 0.2V, or the specific gravity difference is 0.015 or more, the cells will 
require equalization. Please note that only the non-sealed / vented / flooded / wet 
cell batteries are equalized. Do not equalize sealed / VRLA type of AGM or Gel  
Cell Batteries.

7.10  STATE OF DISCHARGE OF A LOADED BATTERY – LOW BATTERY 

/ DC INPUT VOLTAGE ALARM AND SHUTDOWN IN INVERTERS

Most inverter hardware estimate the State of Discharge of the loaded battery by 
measuring the voltage at the inverter’s DC input terminals (considering that the DC 
input cables are thick enough to allow a negligible voltage drop between the battery 
and the inverter).

Inverters are provided with a buzzer alarm to warn that the loaded battery has been 
deeply discharged to around 80% of the rated capacity. Normally, the buzzer alarm 
is triggered when the voltage at the DC input terminals of the inverter has dropped 
to around 10.7V for a 12V battery or 21.4V for 24V battery at C-Rate discharge 
current of C/5 Amps and electrolyte temp. of 26,7° C.
 The inverter is shut down if the 
terminal voltage at C/5 discharge current falls further to 10V for 12V battery (20V for 
24V battery).

The State of Discharge of a battery is estimated based on the measured terminal 
voltage of the battery. The terminal voltage of the battery is dependent upon  
the following:
-  Temperature of the battery electrolyte: Temperature of the electrolyte affects 

the electrochemical reactions inside the battery and produces a Negative Voltage 

Содержание SWI 3000-12





















































Отзывы: