background image

 

Operator's Manual 

Round bale wrapper 

Spin S, Spin F

 

 

- 7 - 

4. SAFETY PRECAUTIONS 

 

During  operation  and  repair  of  the  wrapping  machine,  all  relevant  farming  health  and  safety 
regulations must be complied with. 

 

Only  an  adult  with  a  valid  farming  tractor  driver’s  license  and  familiarized  with  the 
occupational  health  and  safety  regulations  regarding  the  farming  equipment  and  the  following 
manual may operate this machine. 

 

The  following  manual  must  be  read  and  adhered  to,  paying  special  attention  to  directions 
regarding the safe operation of the wrapping machine. 

 

The  manual  indicates  the  machine  parts  which  pose  a  potential  threat.  Hazardous  areas  are 
marked with yellow stickers with warning symbols. Pay special attention to the hazardous areas 
and strictly adhere to the rules. 

 

The operator must familiarize themselves with the meaning of warning symbols. 

 

It is forbidden to operate the wrapping machine  without the safety  guards installed on moving 
components. 

 

Every time before the wrapping machine s started, check the condition and completeness of the 
machine and positioning of its safety guards. 

 

Before starting the wrapping machine and before entering public roads, check the attachment of 
the machine to the tractor. 

 

All adjustment, repair and maintenance works shall be conducted with the tractor engine turned 
off and making sure that the machine is secured against accidental activation. 

 

Before  commencing  loading  and  during  this  process,  make  sure  that  where  are  no  bystanders, 
especially children, nearby. 

 

Exercise  extreme  caution  when  working  on  an  inclined  terrain.  Note  that  the  bales  may  roll 
down slopes. 

 

It is forbidden to operate the wrapping machine with any of the assemblies lifted. 

 

Do not stand between the wrapping machine and the tractor when the tractor engine is running. 

 

Exercise  extreme  caution  when  coupling  and  uncoupling  the  wrapping  machine  with/from  the 
tractor. The machine should be coupled with the tractor equipped with a three point hitch able to 
withstand the vertical load larger than the weight of the wrapping machine. (point 3.1. 

). 

 

During operation, use appropriate protective clothing and shoes with anti-skid soles. 

 

While  loading  the  wrapping  film,  the  tractor  engine  must  be  turned  off  and  protected  against 
accidental activation (ignition key removed, parking brake on). 

 

It  is  forbidden  to  operate  damaged  hydraulic  lines.  The  damaged  lines  must  be  immediately 
replaced with new ones. During the replacement of hydraulic lines, use impermeable protective 
clothing. 

 

The machine’s hydraulic system shall only be operated from inside the tractor’s cabin using the 
hydraulic control levers installed in the tractor’s cabin. 

 

Follow the traffic code regulations and the manufacturer’s recommendations when travelling on 
public roads (point 4.3). 

 

Before entering public roads, perform a visual inspection of the transported machine. 

 

It is forbidden to remain on the wrapping machine during transport. 

 

While  travelling  on  public  roads,  it  is  forbidden  to  transport  wrapped  swat  or  silage  on  the 
wrapping machine. 

 

It is forbidden to operate the wrapping machine under influence of alcohol. 

 

It  is  forbidden  to  operate  the  wrapping  machine  while  under  influence  of  drugs  or  medicines 
with similar effects. 

 

It is forbidden to operate the wrapping machine while under influence of medicines which affect 
the  ability  to  drive  vehicles  or  reduce  psychophysical  health  or  cause  concentration  disorders 
and increase reaction time. 

 

It is forbidden to drive the wrapping machine near sources of open flame. 

 

It is required to strictly adhere to the fire protection regulations and to immediately extinguish 
any fire which may occur during the wrapping machine use or at its standstill. 

 

Содержание Spin F








































Отзывы: