background image

 

12 

KDT 

REAR DISC MOWER 

OPERATOR’S  MANUAL

 

 

IMPORTANT:

 Maintenance and adjustment should ONLY be done after the following has occurred: 

 

tractor’s engine has been

 stopped and ignition key has been taken out,  

 

all  rotating  parts  have  come  to  complete  standstill  (NOTE:  cutting  knives  will  rotate  for 
several minutes after engine is turned off),  

 

the cutterbar is on the ground, and  

 

Never tamper with or remove safety devices on the machine or make them inoperable. 

 

Before starting work and periodically thereafter, replace any damaged, missing and/or worn knives 
and knife holders. 

 

When  driving  on  public  roads  always  comply  with  local  traffic  regulations,  especially  those 
concerning warning lights. 

 

When  the  mower  is  lifted  for  repair  on  3-point  linkage,  it  should  be  secured  against  falling  by 
mechanical support or by chain. 

 

The  bolts  and  other  fasteners  have  to  be  periodically  checked  and,  if  necessary,  tightened  or 
replaced. DO NOT work with damaged or worn fasteners. 

 

Never lift the mower on tractor linkage when the drive is operating and the cutting discs are rotating. 

 

When operating the mower, the tractor should always be equipped with operator protection that is 
required by laws and regulations. 

 

Never start the mower when the mower blades are off the ground. 

 

Before you start the tractor make sure that all drives are turned off and the levers that turn the 
hydraulics are in neutral position. 

 

Never leave 

tractor’s engine running without supervision. Before you leave the tractor, turn off the 

engine and remove the key from tractor’s ignition.

 

 

DO NOT operate the mower when driving the tractor backwards. 

 

Permissible inclination of the mower on a slope when w

orking and during transport is 8°.  Exceeding 

this incline can result in mower tipover. 

 

Never stand between tractor and mower unless tractor and mower are secured against moving by 

the tractor’s brake.

 

 

If any maintenance must be done under an elevated mower, it must be blocked or otherwise secured 
against falling. 

 

When the parts of the mower need replacement, use only original spare parts as described in the 

spare parts list. Pay particular attention to PTO shaft’s guards and mower’s and tractor’s spline 

shaft guards. 

 

Hydraulic hoses are potentially very dangerous. Do the following to minimize any hazards: 

 

Hydraulic  hoses  should  be  periodically  checked  and  if  any  damage  to  the  hoses  have 
occurred or if they have been used more than 5 years, replace with new ones. 

 

Never use scotch tape to repair hydraulic hoses. 

 

When  connecting  hydraulic  hoses  to  tractor’s  hydraulic  connectors,  make  sure  that  the 
tractor’s or mower’s hydraulic system is not under pressure.

 

 

The mower should be stored under a roof and in a way as to not be hazardous bot people or animals. 

 

In the event of an accident involving this mower in a field or on a road, follow all applicable first aid 
procedures and contact SaMASZ technical service. 

 

Mower should be kept clean, so as to avoid danger of fire. 

 

No person and no objects must remain on the mower when driving or transporting. 

Содержание KDT 220





















































Отзывы: