Saluki DSO1000 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 66

background image

Tel: 886.2.2175 2930 Email: [email protected]

www.salukitec.com

47

Trigger Slope

Adjusted

Trigger Type

Edge

Trigger Video Sync

Adjusted

Trigger Video Standard

Adjusted

Vertical Bandwidth

Full

Vertical Coupling

DC (if GND was chosen before); AC for the video signal; otherwise, unchanged

VOLTS/DIV

Adjusted

The Autoset function examines all channels for signals and displays corresponding waveforms. Autoset determines
the trigger source according to the following conditions.



If multiply channels get signals, the oscilloscope will use the channel with the lowest frequency signal as the
trigger source.



If no signals are found, the oscilloscope will use the lowest-numbered channel displayed in Autoset as the
trigger source.



If no signals are found and no channels are displayed, the oscilloscope will display and use Channel 1 as the
trigger source.

Sine Wave:
When you use the Autoset function and the oscilloscope determines that the signal is similar to a sine wave, the
oscilloscope displays the following options.

Sine Wave Options

Details

Multi-cycle Sine

Display multiple cycles that have appropriate vertical and horizontal scales.

Single-cycle Sine

Set the horizontal scale to display about one cycle of the waveform.

FFT

Convert the input time-domain signal to its frequency components and display the result as a graph of
frequency versus amplitude (spectrum). Since it is a math calculation, see

Section 5.3.1 Math FFT

for

more information.

Undo Setup

Let the oscilloscope recall the previous setup.

Square Wave or Pulse:
When you use the Autoset function and the oscilloscope determines that the signal is similar to a square wave or
pulse, the oscilloscope displays the following options.

Square Wave Options

Details

Multi-cycle Square

Display multiple cycles that have appropriate vertical and horizontal scales.

Single-cycle Square

Set the horizontal scale to display about one cycle of the waveform. The oscilloscope displays Min,
Mean and Positive Width automatic measurements.

Rising Edge

Display the rising edge.

«
...
45
46
47
48
49
...
»

Содержание DSO1000



































































Отзывы:

Нет отзывов

Похожие инструкции для DSO1000

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: Gardena Страницы: 19

Бренд: Jackco Страницы: 6

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренд: M-Audio Страницы: 4

Бренд: M-Audio Страницы: 52

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды