background image

 6

APD-100 Automatic Powder Dispenser User Instructions

General information and warnings

1.2 Safety

Failure to properly operate the scale can result in severe injury and/or damage to the 
equipment. Keep this manual as a permanent part of the reloading equipment at all 
times for reference.

1.2.1 General

Use all equipment as recommended.

Keep all equipment and tools clean and orderly. Promptly clean up any powder and 
primer spills.

Do not reload when you are fatigued, ill or under the influence of medications or 
alcohol. Reload only when you can give the procedure your undivided attention. Don’t 
rush and develop a routine to avoid mistakes.

Always wear adequate eye protection.

1.2.2 Primers and Powder

Store primers and powder beyond the reach of children and away from heat, 
dampness, open flames and electrical equipment. Avoid areas where static electricity 
is evident.

Do not use primers of unknown identity. Discard unknown primers in accordance with 
applicable regulations.

Keep primers in the original factory container until ready to use. Return unused primers 
to the same factory packaging for safety and to preserve their identity and shelf life. 
Primer packaging is designed to provide safe storage.

DO NOT store primers in bulk. The blast of just a few hundred primers is sufficient to 
cause serious injury to anyone nearby.

DO NOT force primers. Use care in handling primers.

WARNING! 
This is a Warning symbol. 
Warnings mean that failure to follow specific practices and procedures may 
have major consequences such as injury or death.

CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result 
in damage to equipment or corruption to and loss of data.

NOTE: This is a Note symbol. Notes give additional and important information, hints 
and tips that help you to use your product.

Содержание APD-100





































Отзывы: