background image

APD-100 Automatic Powder Dispenser User Instructions

11

1.9    FCC and EMC declarations of compliance

1.9 FCC and EMC declarations of compliance

United States

Canada

European Countries

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own 
expense.

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio 
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de 
la Classe A prescrites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des Communications du Canada.

WARNING:

 This is a Class A product. In a domestic environment, this product may cause radio interference in which the user may be 

required to take adequate measures.

Содержание APD-100





































Отзывы: