Salamander CT FORCE series, Инструкция по установке и гарантийный талон

Страница: 4 / 17

4 5
The stored hot water temperature must not
exceed 60ºC.
Ensure that the hot supply to the pump is via
a Salamander approved method. (Figure 3, 6 &
7).
Jointing compounds (boss white, hemp and
steel wool) must not be used. Solder fluxes
must not come into contact with the pump.
The anti-vibration hoses must not be twisted
or bent.
Higher rated fuses must not be used.
Product Description
Salamander pumps are suitable for pressure boosting vented stored water systems but
please note that inlet pressures to the pump and water temperatures must not exceed values
stated in the technical specifications.
Installation instructions
Please follow these installation instructions carefully. Failure to install your pump in
accordance with these instructions will invalidate your warranty. Any queries should be
directed to PumpWise on 0191 516 2002 (01844-3212 ROI).
Do not use Salamander pumps for applications other than those stated within the pump
description, or connect the pump directly to the cold mains.
To do so invalidates the warranty.
The plumbing installation must comply with “The Water Supply (Water Fittings) Regulations
1999”, “BS 6700”, and building regulations.
Salamander pumps should be installed by a competent person and supervision in their use
should be given to children or anyone with impaired physical or mental capabilities
Please note that:
• CT Xtra 50, 50+, 54, 75, 75+ & 79 are shower specific pumps.
• CT FORCE 15 PT, 15 IPT, 20 PT, 20 IPT, 30 PT & 30 IPT, CT Bathroom 60B, 80B, and CT
Xtra 64H, 69H & 84H are whole house pumps
• CT FORCE 15 TU, 15 ITU, 20 TU, 20 ITU, 20 SU, 20 ISU, 30 TU, 30 ITU, 30 SU & 30 ISU,
CT Bathroom, 60BU & 80BU , and CT Xtra 64 HU, 69HU & 84HU are universal pumps.
• CT FORCE 20 PS, 20 IPS, 30 PS & 30 IPS, CT Xtra 55, 55+ & 59, 85, 85+, & 89 are positive
single impellor pumps.
• Inlets and outlets must be vertical and plumbed appropriately.
It is essential to ensure that: The cold stored water capacity is adequate for the entire
household requirements (eg minimum 136 litres (30 gal) for shower only, 227 litres (50 gal)
per bathroom, or 364 litres (80 gal) for one bathroom plus an en-suite shower room).
There is a maximum static head of 10 metres (100kPa/1.0Bar).
Cold supplies to the cylinder and the pump are taken from the opposite side of the cold
water storage cistern to the cold mains inlet. The bottom of the cold water storage cistern
must also be checked and cleared of debris (Figure 1).
In systems with more than two bathrooms,
the cold water supply to the cylinder must
be in 28mm pipework.
Multiple cold water storage cisterns must
be linked in accordance with the current
plumbing regulations with the bottom
of the cisterns level.
Never put a non-return valve, restricted
ballofix or an air vent on the supply pipework
to the pump.
Outlet
to cylinder
Inlet
Bottom of cold cistern
must be cleared of debris
Outlet to pump
A Salamander S flange or one
of the 22mm approved top entry
flanges (see page 14)
22mm No Stop Essex flange with
76mm dip pipe and birds beak cut
end to limit air being drawn into
the pump
Indirect coil
Pump inlet
Outlet
OR ALTERNATIVELY
Pump at the base of cylinder
MAX
60°C
Cold water storage
Inlet
Min 600mm
Air vents,
both hot
and cold
Outlet
Vent and
other services
No Stop Essex Flange
MUST be used with
an anti-gravity loop at
least 200mm in depth
MAX
60°C
MAX
60°C
Inlet
Outlet
Figure 1: Tank inlet and outlet position
Figure 3: Hot water supply method
Figure 4: Anti-gravity loop - pumps above the hot water cylinder
The best method is the no
stop Essex Flange with an
anti-gravity loop at least
400mm in depth