manualshive.com logo in svg

Salamander Pumps AccuBoost Series, Инструкция по установке и гарантийный талон, Страница: 22 / 28

Поделиться
Скачать
Salamander Pumps AccuBoost Series Скачать руководство пользователя страница 22

20

12. Technical Specification

Part Number 

ACC-060-SYS ACC-120-SYS ACC-180-SYS

ACC-300-SYS ACC-450-SYS

Guarantee

 3 years

Specification

Maximum operating pressure

8.6 Bar/860 kPa

Ambient temperature range

4

°

C to 49 

°

C

Vessel size (litres)

55

112

178

301

453

Maximum vessel water storage 

capacity (litres)

27.5

56

89

150.5

226.5

Dimensions

Height (mm)

 675

1126

1081

1633

1863

Width (mm)

457 

457

557

557

651

Depth (mm)

480

480

557

557

635

Weights

Empty weight (Kg)

15.4

20

27.5

42.7

54.2

Filled weight (Kg)

42.9

76

116.5

193.2

280.7

Maximum weight (Kg)

70.4

132

205.5

343.7

507.2

Pump

Pump type

Regenerative

Pump model

ASSYACCUFORCE

Mechanical seal

Nitrile/carbon/ceramic

Pump body/impeller

Brass

Enclosure protection

IPX2

Motor

Type

Capacitor start and run induction motor

Duty rating

Continuous

Electrical

Power supply/phase/frequency

230 V/1/50 Hz

Current (Full load)

1.9 A

Power consumption

410 W

Fuse Rating

3 A

Power cable

Pre-wired with plug

Connections

Pump

3/4” male BSP

Anti vibration couplers

3/4” female BSP - 22mm push-in

Performance

Maximum head

4 Bar/400 kPa

Maximum flow rate

14 L/min

16 L/min

18 L/min

30 L/min

36 L/min

Time at maximum flow rate

9 mins

9 mins

9 mins

9 mins

9 mins

Minimum continuous flow rate

12 L/min

12 L/min

12 L/min

12 L/min

12 L/min

Performance values may be higher if mains natural flow is above 12 L/min

Pumped 

Table 3

Note: quoted values may vary due to tolerances and site conditions.

Содержание AccuBoost Series





























Отзывы:

Нет отзывов