Sailrite ULTRAFEED 120931 Скачать руководство пользователя страница 4

 |    

Sailrite.com

SEWING MACHINE SAFETY

•  Do not operate in conditions where you or the 

machine are or may become wet.

•  Operate the machine on a firm, level surface 

where there is adequate room for safe 

operation.

•  Observe caution when placing your hands or 

other parts of your body or clothing near any 

moving parts including but not limited to the 

following: the walking foot, the needle, the 

drive belt, the balance wheel and any of its 

parts.

•  Do not run the machine without its covers.
•  Do not stop the movement of the balance 

wheel with your hands.

•  Use caution in tilting the machine backwards 

in its table and in lowering it back into the 

table.

•  Use proper lifting techniques when moving 

the machine.

•  Do not drop the machine.

•  Always use the proper voltage required for 

the motor and light.

•  Wear protective eyewear when sewing.
•  Wear shoes when operating the foot 

pedal.  

•  Provide supervision when allowing others to 

use the machine—particularly children and 
those who are unfamiliar with the machine’s 
operation.  

•  Do not use around flammable materials.
•  Use both hands to guide the material while 

the belt and balance wheel are in motion.

•  Maintain a safe distance from the belt and 

balance wheel when the machine is in motion.

•  The operator’s hand should not be near the 

wheel pinch point (where moving parts may 
cause harm to the user) except to raise and 
lower the needle, and only when the motor is 
disengaged. 

Please observe the following when using your Sailrite sewing machine

WARNING:

 Some products may be fabricated from materials which may contain chemicals known to 

the state of California to cause cancer, birth defects or other reproductive harm.

Содержание ULTRAFEED 120931

























Отзывы: