Safran LRF 7047 Скачать руководство пользователя страница 25

Страница: 25 / 72

LRF 7047- Integrator Manual

914929_TML_LRF7047_en_Version B

Public: 04.2019

Confidential & Proprietary



Page: 25/72

4.5.2 Boresighting at 830 nm

LRF 7047 is equipped at the factory with an 830 nm pointer. Professional boresighting of the LRF module

with the main optical axis of the host system can be done with the 830 nm pointer. The alignment

procedure is identical to the procedure at 1550 nm, except for the camera. To make the laser spot of 830

nm visible, a regular NIR camera can be attached to the collimator. These cameras are significantly

cheaper than 1550 nm cameras.
The laser pointer is not eyesafe! Appropriate safety measures have to be put in place to use the pointer

for alignment. Keep in mind that the laser pointer is too strong for the camera, for this reason a filter glass

has to be used to attenuate the beam intensity. Please note that the wedge error of the filter has a direct

impact on the alignment accuracy and therefore has to be as small as possible. We recommend using a

filter with a max. wedge error of 10 arcsec.
Filter glass can be sourced, for example, from Schott. Schott Filter glasses KG1, KG2, KG3 or KG5 can

be selected, depending on the required attenuation factor.

http://www.schott.com/advanced_optics/english/products/optical-components/optical-filters/optical-filter-

glass/index.html

If such equipment is not available, the 830 nm pointer can also be made visible by using a Night Vision

device. By using a boresight chart at a defined distance, the LRF can be aligned by bringing the main

optical axis of the host system and the LRF to the predefined positions on the boresight chart.

4.5.3 Back-up solution

If no other optical equipment is available, an alternative method can be

used to show the path of the invisible laser light. Place a vertical and

horizontal small pole (approx. 10 cm of width) at about 200 meters

distance. Start with one orientation (horizontal or vertical) and measure

until the laser hits the pole and gives the correct distance back. You can

then center the laser to this first orientation and then do the same with

the second orientation. With this method you can align the laser to any

equipment, however its more time consuming and not as precise as

with a camera.

A quick and easy tool to make laser light visible are laser viewing cards. These cards have a

photosensitive area which emits a visible spot at the location of the laser beam. However, this only works

when the card is quite close to the LRF module. To see the laser beam of LRF 7047 modules, the laser

viewing card must absorb light of 1550 nm wavelength (or 830 nm if the optional pointer is available).

Vendors of such cards are:



Laser2000 (

www.laser2000.de

) (e.g. QTX-Q42-T)



Thor Labs (

www.thorlabs.de

) (e.g. VCR4)

Figure 15: Boresighting

Содержание LRF 7047




































































Результаты поиска

Содержание LRF 7047

Отзывы:

Похожие инструкции для LRF 7047

Бренды по названию

Популярные бренды

Safran LRF 7047, Руководство пользователя

Результаты поиска

Содержание LRF 7047

Отзывы:

Похожие инструкции для LRF 7047

Бренды по названию

Популярные бренды