background image

22

6.4 

Connecting to the V-Line System

The V-Line top bracket has a single point anchor to assist the transistion from the V-Line 
system to another fall protection system. See Figure  28.

 

Do not connect to any other part of the system.

Figure 28 

Storage, Transport and Maintenance

7.1 

Storage and transport

This equipment shall be stored and transported in a cool, dry environment, away from any 
hazards and out of direct sunlight. 

7.2 

Maintenance

7.2.1  The V-Line system is serviceable only by trained and authorised installers. Contact 
SafetyLink to find your nearest available installer. The service interval will be determined by 
the condition in which it is used. Harsher conditions will require more frequent servicing. The 
equipment may remain in service until it fails an inspection or is involved in a fall. 
7.2.2  The V-Line Shuttle is non serviceable. The equipment may remain in service until it 
fails an inspection or is involved in a fall.

 

Do not attempt to modify or disassemble this product.

7.3 

Cleaning

The V-Line Vertical Lifeline may be cleaned by the end user periodically to increase service 
life. After cleaning, the product shall undergo the pre-use inspection. 

Cable and Brackets - Clean with a rag and warm water to remove dirt and grit. A mild detergent 
may be used to remove grease or oils from the product.

Shuttle - Clean Shuttle with a rag and warm water to remove dirt and grit. A mild detergent 
may be used to remove grease or oils from the product.

 

Do not store this product when wet. Allow the product to dry and conduct a pre-use 

inspection prior to return the item to service.

Содержание V-Line VLINESHUT001




























Отзывы: