background image

 

IN CASE OF ACCIDENT 

 

 

A FALL RESCUE PLAN AND SAFE WORK STATEMENT MUST BE DEVELOPED PRIOR TO USING 
SAFETYLINK SYSTEMS AND EQUIPMENT.   

 

PERSONS WORKING AT HEIGHTS SHOULD NOT WORK ALONE. 

 

It is critical that before using any SafetyLink Systems a fall rescue plan is in place for any persons suspended 
mid-

air following a fall. Serious injury or death can occur in a matter of minutes, particularly if a person’s 

movement or breathing is restricted or loss of consciousness has occurred. In accordance with your fall 
rescue plan and appropriate first aid procedures it is essential to remove the person from the suspended 
position as quickly as possible.

 

 

IN ACCORDANCE WITH AS/NZS 1891.4:2009 CLAUSE 9.5 

 

EQUIPMENT WHICH HAS ARRESTED A FALL OR SHOWS A DEFECT

 

Any piece of equipment including both personal and permanently installed items, which has been used to 
arrest a fall or which shows any defect during operator or periodic inspection shall be withdrawn from 
service immediately and a replacement obtained if necessary. A label indicating the condition or defect 
should be attached to the equipment, and it should be examined by a competent height safety installer 
who  will  decide  whether  the  equipment  is  to  be  destroyed  or  repaired  if  necessary  and  returned  to 
service. In the latter case, details of any repair shall be documented, and a copy given to the operator.  

 
 

 

 

 

Terms/Conditions/Warranties

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

DISTRIBUTOR: 

Safety

Link

 Pty Ltd | ABN 83 081 777 371 

Phone: 1300 789 545 or +61 2 4964 1068| Fax: 1300 738 071 or +61 2 49641069 

[email protected]   | www.safetylink.com

 

 

Содержание LADFX001













Отзывы: