SafeTech AS 900 Series Скачать руководство пользователя страница 18

Страница: 18 / 26

Model ASx-900|

Owner’s

Manual|

Version no: 1

safetech.com.au

Problem

Possible Causes

Remedy

Lift table
creeps down
under load.

1) Down valve spindle is

sticking or contains
debris.

This is the most likely cause of lift table creep. To remedy,
replace the down valve spindle.

Be extremely careful not to allow dirt to enter the system
when replacing the down valve spindle.

2) Check valve in pump

contains debris.

Contact Safetech regarding dismantling and cleaning the
check valve. Alternatively, the pump can be replaced.

3) Oil by-passing cylinder

seals.

Check clear vent tube for by-pass as described in section
4.2.

If by pass occurs, contact Safetech regarding repacking or
replacing cylinders.

6.0 Warranty

Refer to Safetech complete Terms of Sale and Warranty at

http://www.safetech.com.au/terms-sale-warranty/

7.0 Safetech Divisions

Head Office

– Moe, Victoria

Address:

39-45 Della Torre Road, Moe, Victoria, 3825

Postal Address:

PO Box 360, Moe, Victoria, 3825

Phone:

1800 674 566

Email:

[email protected]

Service

Service Enquiries

Phone:

03 8546 5600

Email:

[email protected]

Sales offices

Victoria

Address:

1/21 Lionel Road Mt Waverley VIC 3149

New South Wales

Address:

14a/65 Elizabeth Street Wetherill Park NSW 2164

Queensland

Address:

12-23 Armada Street, Banyo, QLD, 4015

Western Australia

Address:

11/288 Amherst Road Canning Vale, WA 6155

Содержание AS 900 Series



























Результаты поиска

Содержание AS 900 Series

Отзывы:

Похожие инструкции для AS 900 Series

Бренды по названию

Популярные бренды

SafeTech AS 900 Series, Руководство пользователя

Результаты поиска

Содержание AS 900 Series

Отзывы:

Похожие инструкции для AS 900 Series

Бренды по названию

Популярные бренды