Saeco RI9722/11 Скачать руководство пользователя страница 35

Страница: 35 / 224

INCANTO S-CLASS

3. OPERATION

Saeco International Group

REV.1 FEB.2005

Page 19/21

Troubleshooting

Fault/Indicator

Possible cause

Remedy

Does not function

No power

Check mains plug / mains
circuit breaker.
Ensure machine door is
closed.

BREWING UNIT NOT
DETECTED

Brewing unit not properly installed
or not closed.

Install brewing unit
correctly.

GRINDS CONTAINER
NOT DETECTED

Coffee grinds container not properly
installed.

Brewing unit correctly
installed.

EMPTY GRINDS
CONTAINER

Coffee grinds container full

Empty coffee grinds
container (reset only
possible if machine is turned
on)

COFFEE BEAN
CONTAINER EMPTY

Coffee bean container is empty.

Fill coffee container.

FILL WATER TANK.

Water tank is empty.

Fill water tank

GRINDER OBSTRUCTED

Clean grinder.

DE-AERATE

Air in water system.

Open water nozzle.

REPLACE WATER
FILTER

Replace water reset
user menu

Instead of coffee, only water
is dispensed.

Coffee powder selection button is
pressed, but no coffee powder is
dispensed.

Add one level measure of
coffee powder.

No water / steam

Steam nozzle blocked.

Free opening using a thin
needle.

The coffee flows too quickly

Beans ground too coarsely.

Press knob and turn in the
direction of the small points.

The coffee flows too slowly

Beans ground too finely.

Press knob and turn in the
direction of the large points.

The cups are cold.

Pre-heat cups.

Coffee is not hot enough

Boiler temperature too low.

Increase temperature in user
programme.

Unsuitable coffee blend.

Change brand of coffee.

Coffee is no longer freshly roasted.

Use fresh coffee.

Coffee has no froth.

Beans ground too coarsely or finely.

Change grinding level.

Longer heating time or less
hot water.

The machine is calcified.

Decalcify machine.

The brewing unit cannot be
removed.

The brewing unit is not in home
position.

Turn machine on, close
service door and check
dregs drawer.
(the brewing unit goes
automatically to home
position)

Содержание RI9722/11

































































































































































































































Результаты поиска

Содержание RI9722/11

Отзывы:

Похожие инструкции для RI9722/11

Бренды по названию

Популярные бренды

Saeco RI9722/11, Руководство по обслуживанию

Результаты поиска

Содержание RI9722/11

Отзывы:

Похожие инструкции для RI9722/11

Бренды по названию

Популярные бренды