Saeco RI9722/11 Скачать руководство пользователя страница 129

Страница: 129 / 224

INCANTO

3. OPERATION

Saeco International Group

REV.5 FEB.2005

Page 3/16

Descaling procedure

Action

Comments

Descale LED indicator

Descaling

Fill water tank with commercial
descaler according to the relevant
instructions.

Light flashes

Place an appropriately sized
container under the HWS nozzle.

Light flashes

Keep the descaling button
pressed for about 5 sec.

Descaling programme is activated.

Open HWS valve

The pipes are rinsed with descaler
at intervals. (Duration: approx. 45
min)

Light flashes

Programme end

LED of all 5 buttons flash

Close HWS valve

Descaling programme complete.

Off

Rinse (fill tank 2x)

Open HWS valve

Off

Troubleshooting

Fault

Remedy

No display

No power supply to machine.

Check mains fuses / Is machine plugged in? / Is main
switch turned on?

Water instead of coffee

(powder button pressed)

- Place a measuring spoonful of coffee powder in the
powder compartment

- Pre-heat cups

- Clean brewing unit if necessary

Coffee is not hot enough

- Descale if necessary

No hot water/steam

Hot water/steam nozzle blocked

- Clean nozzle out with needle

(with machine turned off and closed rotary
valve/HWS valve).

Heating time too long, water quantity
insufficient

- Descale machine

The brewing unit cannot be removed.

- Close service door.
- Turn machine on (brewing unit moves to home
position)

The brewing unit cannot be removed.

- Bring brewing unit to initial position.

Cannot dispense

The descaling indicator flashes

(machine not locked)

- Descale

Expresso, coffee and steam buttons
flash

- Overheating: Remove hot water until only expresso
and coffee buttons are lit

Water LED lights up

- Fill with fresh water

Water LED flashes

- De-aerate machine

Coffee beans/Dregs LED lights up

- Fill with coffee beans

Coffee beans/grinds container LED
flashes

- Empty grinds container

(machine must be turned on)

Warning LED lights up

- Correctly install brewing unit, drip tray and grinds
container.

Warning LED flashes

- Grinder obstructed
- Gears obstructed
- Contact an authorised service centre

Содержание RI9722/11

































































































































































































































Результаты поиска

Содержание RI9722/11

Отзывы:

Похожие инструкции для RI9722/11

Бренды по названию

Популярные бренды

Saeco RI9722/11, Руководство по обслуживанию

Результаты поиска

Содержание RI9722/11

Отзывы:

Похожие инструкции для RI9722/11

Бренды по названию

Популярные бренды