Saeco D.A. 8P Instant, Эксплуатация и обслуживание

Страница: 32 / 40

English
32
- Rotate cup dispensing tube (ref. A , fig. 22) pressing TS4 and
TS5 (fig. 8), until the opening preset for cup insertion is turned
into H position (fig. 22).
- Insert a quantity of cups between minimum and maximum lev-
els printed on the applied labels.
- Rotate cup dispensing tube (ref. A , fig. 22) pressing TS4 and
TS5 (fig. 8), until the opening preset for cup insertion is turned
into Y position (fig. 22).
- Insert in the remaining provided spaces (ref. D , fig. 23) a
quantity of cups between minimum and maximum levels printed
on the labels applied to each cup spaces.
Important
Verify that the action of the springs does not block the cup
dropping into the cup bracket (ref.
23
, fig. 1). Use cups suit-
able to automatic dispensing, without defects and fit for the
size printed on the label applied on the cup dispenser (ref.
22 , fig. 1 e 22).
- Reclose both cup dispenser door and front door.
Vending machine operation
- Enable electric functions (main switch in “ I ” position).
Fill vending machine water circuit proceeding as follows:
-
Open front door;
- Insert the key (ref. A , fig. 5) to activate safety microswitches.
Important
This operation, necessary for vending machine installation,
disables the safety system provided on the door opening.
Therefore, it has to be performed by skilled personnel, with
knowledge of risks working on live equipment.
- open coiner support plate (ref. 19 , fig. 1);
- press and hold TS3 key (fig. 8) until a regular water jet comes
out from the dispensing channel of last mixer;
- close coiner support plate (ref. 19 , fig. 1);
- remove the key to disable safety microswitches (ref. A , fig. 5);
- close front door;
- wait until (ref. 2 , fig. 1) “
W A I T W A I T W A I T W A I T W A I T
” appears (vending machine
is warming up) on display;
- read (ref. 2 , fig. 1) the vending machine dialog message on
display and execute displayed operations;
- wait until display shows the message in “
TEXT STAND- TEXT STAND- TEXT STAND- TEXT STAND- TEXT STAND-
B Y B Y
B Y B Y B Y ” (normally is
*SAECO DA 8P* *SAECO DA 8P*
*SAECO DA 8P* *SAECO DA 8P* *SAECO DA 8P* ) function.
Important
Dispensed products must be used quickly, and cannot be stored
and/or packed.
- Verify vending machine operation by dispensing some bever-
ages.
Important
All keys are originally programmed on standard values, in
any case you must check that the beverage matches to de-
sired characteristics. Otherwise dispensing keys have to be
reprogrammed (see “7 -Programming” ).
8.3 Beverage dispensing
- Choose beverage among those available.
- If the vending machine has not been programmed to freely
dispense beverages insert requested credit.
-
Display shows “
SELECT BEVERAGE SELECT BEVERAGE SELECT BEVERAGE SELECT BEVERAGE SELECT BEVERAGE
” .
- Press the key corresponding to requested beverage.
Important
To avoid burns, wait for end of operation signal (“
R E M O V E R E M O V E R E M O V E R E M O V E R E M O V E
C U P C U P
C U P C U P C U P
” appears on display) before putting your hand into the
dispensing opening.
8.4 Messages and signals of special
situations
Vending machine operation is completely, or partly, blocked when
some products are missing or abnormal condition occurs. Display
located on the control panel provides the reasons that caused the
block.
When a trouble occurs to the vending machine, a message (ex.:
“
CALL ASSISTANCE – OUT OF SERVICE CALL ASSISTANCE – OUT OF SERVICE CALL ASSISTANCE – OUT OF SERVICE CALL ASSISTANCE – OUT OF SERVICE CALL ASSISTANCE – OUT OF SERVICE
0 1 0 1
0 1 0 1 0 1 ” ) appears on display.
The number that follows the indication “
OUT OF SERV- OUT OF SERV- OUT OF SERV- OUT OF SERV- OUT OF SERV-
I C E I C E I C E I C E I C E
”, is the code of said trouble.
To display the type of trouble, you need to:
-
open front door;
- insert key to exclude safety (ref. A , fig. 5);
- open coiner support plate (ref. 19 , fig. 1);
- press “RESET” key (ref. TS2 , fig. 8);
- display shows the message concerning the type of trouble
occurred (ex.: “
CALL ASSISTANCE - NO WA- CALL ASSISTANCE - NO WA-
CALL ASSISTANCE - NO WA- CALL ASSISTANCE - NO WA- CALL ASSISTANCE - NO WA-
T E R T E R
T E R T E R T E R ”).
Once the trouble has been eliminated, you need to:
-
press “RESET” key again (ref. TS2 , fig. 8) to RESET;
- close coiner support plate (ref. 19 , fig. 1);
- remove the safety disabling key and close front door.
Danger
This operation, that disables the safety system, has to be per-
formed by a Maintenance Technician, who is aware of risks re-
sulting from the presence of organs under tension or moving.