2 - 6
3/5/97
UNIFIED INCH TORQUE VALUES
SPECIFICATIONS & INFORMATION
UNIFIED INCH TORQUE VALUES
DO NOT use these values if a different torque value or tightening procedure is given for a specific application.
Torque values listed are for general use only. Check tightness of fasteners periodically.
Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade.
Fasteners should be replaced with the same or higher grade. If higher grade fasteners are used, these should only
be tightened to the strength of the original.
Make sure fasteners threads are clean and that you properly start thread engagement. This will prevent them from
failing when tightening.
Tighten plastic insert or crimped steel-type lock nuts to approximately 50 percent of the dry torque shown in the
chart, applied to the nut, not to the bolt head.
Tighten toothed or serrated-type lock nuts to the full torque value.
a
“Lubricated” means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings.
“Dry” means plain or zinc plated without any lubrication.
b
Grade 2 applies for hex cap screws (not hex bolts) up to 152 mm (6 in.) long. Grade 1 applies for hex cap screws over
152 mm (6 in.) long, and for all other types of bolts and screws of any length.
Size
Grade 1
Grade 2
b
Grade 5, 5.1 or 5.2
Grade 8 or 8.2
Lubricated
a
Dry
a
Lubricated
a
Dry
a
Lubricated
a
Dry
a
Lubricated
a
Dry
a
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
Nm
lb-ft
1/4
3.8
2.8
4.7
3.5
6
4.4
7.5
5.5
9.5
7
12
9
13.5
10
17
12.5
5/16
7.7
5.7
9.8
7.2
12
9
15.5
11.5
19.5
14.5
25
18.5
28
20.5
35
26
3/8
13.5
10
17.5
13
22
16
27.5
20
35
26
44
32.5
49
36
63
46
7/16
22
16
28
20.5
35
26
44
32.5
56
41
70
52
80
59
100
74
1/2
34
25
42
31
53
39
67
49
85
63
110
80
120
88
155
115
9/16
48
35.5
60
45
76
56
95
70
125
92
155
115
175
130
220
165
5/8
67
49
85
63
105
77
135
100
170
125
215
160
240
175
305
225
3/4
120
88
150
110
190
140
240
175
300
220
380
280
425
315
540
400
7/8
190
140
240
175
190
140
240
175
490
360
615
455
690
510
870
640
1
285
210
360
265
285
210
360
265
730
540
920
680
1030 760
1300 960
1-1/8 400
300
510
375
400
300
510
375
910
670
1150 850
1450 1075 1850 1350
1-1/4 570
420
725
535
570
420
725
535
1280 945
1630 1200 2050 1500 2600 1920
1-3/8 750
550
950
700
750
550
950
700
1700 1250 2140 1580 2700 2000 3400 2500
1-1/2 990
730
1250 930
990
730
1250 930
2250 1650 2850 2100 3600 2650 4550 3350
1 or 2
b
2
5
5.1
5.2
5
8
8.2
8
No Marks
No Marks
SAE
Grade
and Nut
Markings
SAE
Grade
and Head
Markings
www.servicemanualall.com
Содержание 1338 Gear
