Sabo 47-PRO VARIO, Руководство оператора

Страница: 42 / 88

10
authorized specialist workshop. An improperly sharpened or unbalanced blade
can cause severe vibrations, and damage the lawnmower.
The cutting edges of the cutting blade may be grinded only until the respective value
(see illustration
Q ) or the marking (1) on the cutting blade (ring) has been reached.
Attention! Observe the grinding angle of 30°.
Your professional workshop can check this value - (grinding limit) for you!
WARNING
A blade by which the wear limit (marking) has been exceeded can break off and
spin away; this can cause severe injuries.
Replacing the blade
WARNING
The cutting blade bar must always be replaced by an authorised workshop. A
wrongly assembled cutting blade coupling or a blade screw that is tightened too
tightly or too loosely can allow the cutting blade bar to become loose and cause
severe injuries.
– Only use genuine cutter bars for replacement. Non-equivalent spare parts can
damage the machine and are a safety hazard.
– Replacement cutting tool must be marked permanently with the name and/or
company logo of the manufacturer or supplier and the part number.
Servicing the front wheels
The wheels are equipped with maintenance-free bearings. Maintenance is not required.
Servicing the rear wheel drive (Illustration R )
Lubricate the wheel bearings every 50 operating hours.
– Pull the drive wheels off after loosening the nuts and removing the dust cap from
the wheel axle.
– Remove the wheel cover, pay attention to the thrust washer.
– Remove any soiling from the wheel cover, the free-wheeling pinion on the gear
shaft and the gear rim on the inside of the wheel.
NOTE
Do not remove the free wheel pinion from the gear shaft!
– Lubricate the wheel axle using the roller bearing grease "KAJO-Longlife grease
LZR 2". Do not lubricate the free-wheeling pinion and gear rim in the wheel!
– Set the wheel cover in place and push the start-up disc onto the wheel axle. When
putting the drive wheel in place make sure the pinion and gear rim interlock, turn
the wheel on the axle slightly to achieve this if necessary.
– Set the dust cap in place, fix using the hexagon nut and tighten to such an extent
that the wheels can just about turn easily but without play.
Servicing the drive
– It is absolutely essential that the Bowden cable runs easily for switching on and off,
so that the control drive works perfectly.
Changing the drive V-belt
The drive V-belt must be replaced by a specialist workshop.
18 SERVICING THE ENGINE
Safety instruction!
See table for explanation of symbols
page 3
WARNING
Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause
serious illness or death.
Do not run an engine in an enclosed area, such as a garage, even with doors and
windows open.
Move the machine to an outside area before starting the engine.
IMPORTANT
For cleaning and maintenance work, always close the petrol tap A , tilt the
mower forwards O (spark plug facing upwards). If it should become necessary
to place the mower on its side, then place it on the exhaust side, never on the
carburetor side, as otherwise start-up problems could occur.
When tilting the mower forwards make sure the ejection flap does not get
damaged. Secure the mower in its raised position!
ATTENTION
When tilting or placing the mower on its side, ensure that no oil or fuel comes out
of the machine. Fire hazard!
The regular implementation of the prescribed maintenance and care work are the
prerequisite for a permanent and fault-free functionality of the motor and also the basic
requirement for any guarantee claims.
The motor should be kept clean, particularly on the outside, and the silencer and
cylinder area must always be kept free from foreign bodies (e.g. grass residue). The
exhaust and motor reach very high temperatures when in use. Flammable foreign
bodies such as foliage, grass etc. may catch fire.
Perfect cooling can also only ensured when cylinder ribs are always clean.
IMPORTANT
Never use a pressure cleaner or ordinary water jet to clean the motor. Damages
or expensive repairs can be the consequence of such action.
Oil change
NOTE
For environmental reasons, we recommend that the oil change is performed by
an authorised workshop.
The first oil change in a new engine is required after approx. 20 operating hours. Later,
it should be done every 50 operating hours or at least once per mowing season.
– Before the engine or the equipment is tilted to drain oil, empty the petrol tank and
let the engine to run until it stops due to lack of fuel.
– Stop the engine and remove the spark plug connector.
– Renew the oil so long as the engine is warm.
– To replace the oil, remove the dipstick from the oil filler neck and set the mower on
its side so that the used oil can drain into a container.
Do not drain used oil into the sewage system or soil; dispose of it according
to the local regulations.
– Position the mower straight and fill brand-name oil into the spout (for quantity and
quality, see technical data). Insert the dipstick but do not screw it tight, check the
oil level (see chapter
Filling oil , illustration Y1 )! If the oil level is correct, insert the
dipstick again and tighten it.
Cleaning and replacing the air filter (Illustration W )
IMPORTANT
Never let the engine start or run whilst the air filter is removed.
– Open the cover (1), pull down and out and remove.
– Remove the paper filter insert (2) and pre-filter (3). To remove the pre-filter from
the cover, remove the grid (4) first.
– Clean the paper filter insert every 50 operating hours
Knock gently onto a smooth surface if soiled lightly. Replace if heavily soiled or
damaged. Do not wash out paper filters, nor blow them out with compressed air or
grease them.
– Clean the pre-filter every 50 operating hours.
Wash pre-filters in hot water with liquid detergent, rinse them out in clean water,
press out excess water and allow to dry thoroughly in air. Do not lubricate the pre-
filter with oil.
– After cleaning or replacement, insert the filter element into the air filter plate, insert
the pre-filter in the cover and fix in place with the grid.
– Insert the hooks (5) on the cover (1) into the seat (6) at the bottom in the air filter
plate.
– Tilt the cover upwards and close with care.
In the case of unfavourable operation conditions (severe formation of dust), cleaning is
required after every mowing process. Replace the paper filter element and pre-filter
annually or every 100 operation hours.
(Please see original spare parts and accessories for order no. of filter element)
Checking the spark plug (Illustration Y )
To check for wear, remove the spark plug connector and unscrew the spark plug. If the
electrode is badly worn the spark plug must be replaced as a matter of course. (Order
no. see original spare parts list and accessories).
Otherwise it is sufficient to clean the spark plug and set the electrode gap to 0.6-0.7
mm. Screw the spark plug (pay attention to sealing ring) into the engine by hand and
tighten using the socket wrench. Press on spark plug connector. Replace the spark plug
annually.
Correct winter storage of the engine (or when not used for a long period
of time)
– Empty the petrol tank or allow the engine to run until it stops due to lack of fuel.
– Switch off engine and disconnect spark plug cable.
– Drain off the oil while the engine is still warm. Fill with fresh oil (for quantity and
type, see technical data).