Sabo 47-PRO VARIO, Руководство оператора

Страница: 43 / 88

11
– Clean grass and chaff from cylinder and cylinder head fins and around muffler.
– Always keep the machine in a clean condition in a closed, dry room out of reach of
children.
19 TROUBLESHOOTING
Fault Possible cause Remedy
Engine does not start
Control bracket not
pressed down. Press control bracket to
upper part of handlebar
D .
Petrol tap closed. Open the petrol tap A .
Fuel tank is empty. Fill fuel tank with clean and
fresh fuel.
Spark plug connector
loose. Press on spark plug
connector or have it checked
by an authorized dealer.
Spark plug defective or
dirty or electrode burnt
out. Replace or clean spark plug,
set electrode gap to 0.6-0.7
mm
Y .
Excessive petrol supply
to engine (spark plug
wet). Have it checked by an
authorized dealer.
Air filter dirty Clean or replace air filter
insert
W .
Engine power
decreasing
Air filter soiled. Clean or replace the air filter
insert
W .
Spark plug clogged with
soot. Have it checked by an
authorised workshop.
Fuel old or soiled
Empty the petrol tank and fill
with fresh petrol.
Engine runs irregularly
Air filter dirty.
Clean or replace air filter
insert
W .
Spark plug contaminated
with soot. Have it cleaned by an
authorized dealer.
Mower does not work
Pull drive control bar not
pulled. Pull drive control bar G .
Have it checked by an
authorised workshop.
Drive speed cannot be
regulated
Have it checked by an
authorized dealer
Extreme vibration
Have it checked by an
authorized dealer
Cut not clean,
lawn turns yellow
Cutting blade blunt. Have it sharpened and
balanced by an authorised
workshop
Q .
Cutting height too low. Set higher cutting height I .
Motor speed too low. Have it checked by an
authorized dealer
Mowing speed too high.
Adapt mowing speed, switch
motor drive off if necessary.
Insufficient overlap
between mowing lanes. If grass is long, the mowing
lanes may need to overlap
further.
Lawn matted.
A perceptible improvement
can be achieved by using a
scarifier.
Ejector blocked
TurboSignal ignored
J + K .
Empty the collecting bag L .
Engine speed too low. Have it checked by an
authorized dealer
Cutting height too low
with grass too high. Set higher cutting height I .
Mowing speed too fast.
Adapt mowing speed, switch
motor drive off if necessary.
Grass is damp. Allow the lawn to dry.
The mulched grass
does not look good:
clumps, excessive cut
material, coarse cut
Cutting blade blunt.
Have it sharpened and
balanced by an authorised
workshop
.
Mulching rule ignored
(cut max. 1/3 of grass
height; the grass height
to be cut must be less
than 10 cm)
Set higher cutting height I .
Convert mower to rear
ejection
U2 + S1 and mow
lawn with high cutting height
first.
Driving speed too high.
Adapt driving speed, switch
motor drive off if necessary.
Grass accumulation
under the mower blade.
Set higher cutting height I .
Insufficient overlap
between mowing lanes. If grass is long, the mowing
lanes may need to overlap
further.
Grass is damp. Set higher cutting height I .
Allow the lawn to dry.
In case of faults and defects which have not been listed here, please contact the
nearest authorized dealer.
Repairs which require specialized knowledge should only be performed by a qualified
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
perform the maintenance work described here yourself.
20 TECHNICAL DATA
Engine
Engine Yamaha 4-stroke engine, MA190V
Engine displacement 190 cm
3
Engine speed 2800 rpm
Rated input 3.2 kW
Electrode gap 0.6 - 0.7 mm
Fuel Standard unleaded fuel,
with max. 10% ethanol or max. 5% MTBE,
do not use alkylate-based petrol!
Tank contents approx. 1.2 litres
Lubricating oil SAE 10W30, SAE 10W40
4-stroke engine oil API service class SE
or a higher class oil
Oil quantity 0.6 litres
Mower
Housing Die-cast aluminium, with steel inserts
Cutting width 470 mm
Cutting heights Single wheel,
25, 28, 35, 45, 55, 70, 80 mm
Adjustable-height handlebar 3-way
Grass collector capacity 65 litres
Speed 2.7 – 4.5 km/h
Weight 49 kg
Length 1740 mm
Width 510 mm
Height 1075 mm
Wheels front / rear Ø 210 mm / Ø 210 mm
Bearing front Deep groove ball bearing
Bearing rear Bronze-Sleeve bearing
Sound power level
Guaranteed sound power level;
measured according to 2000/14/EC L
wa
= 96 dB(A)