S.R.Smith MultiLift Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 30

S.R.Smith MultiLift Скачать руководство пользователя страница 9

700-9000

6.14.13

9

8. The LiftOperator Control is pre-assembled on the multiLift™ (see LiftOperator Owner’s Manual for

more information). Remove the hand control from accessory
carton and unwrap. Insert plug into large socket on the
LiftOperator control box as shown in Figure 4. Make sure plug
is secure.

9. Ensure that the actuator plug is secured in the socket as

shown in Figure 4.

10. Attach battery to LiftOperator control box making sure that the

battery latch bracket locks into the slots on the control unit
mounting bracket. To remove the battery from the control unit,
pull outward on the battery handle until the battery latch
bracket clears the slots in the control unit mounting bracket,
then pull upward, see Figure 5.

11. Check all controls and emergency stop

button for proper operation. See LiftOperator
Owner’s Manual for details.

12. Attach seat assembly with bolt and thumbnut

in appropriate hole. Refer to Figure 10 and
Table 1 to determine the correct seat
mounting hole to use. Also see Figure 6.

Figure

4. Control Box

CONTROL UNIT MOUNTING BRACKET

BATTERY LATCH
BRACKET

BATTERY HANDLE

2

1

Figure

5. Battery

Attachment/Removal

Figure 6. Seat
Mounting Holes

«
...
7
8
9
10
11
...
»

Содержание MultiLift































Отзывы:

Нет отзывов