S.R.Smith MultiLift Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 30

S.R.Smith MultiLift Скачать руководство пользователя страница 18

700-9000

6.14.13

18

then the issue is likely with the control box, and the control box will need to be
replaced.

Lift will not raise and lower when using the hand control:

1.  Check hand control connection to control box. Be sure plug is pushed in all the way.
2.  Check hand control connection to control box for damaged pins.
3.  Check connection cable for damage.
4.  Use the buttons on the front panel of the control box to raise and lower the lift. If the

lift raises and lowers when using the buttons on the front of the control box, the hand
control should be replaced.

If none of the above steps work in getting the lift to function, call S.R. Smith for assistance.

LONG-TERM STORAGE

When storing the lift for an extended period of time:



Wash seat with disinfectant solution and then rinse with fresh water and dry entire lift



Keep the battery on the charger in a dry temperature controlled area



Cover unit and store in a dry location away from pool chemicals

Questions/Comments - Contact us at 800.824.4387 or 503-266-2231 or [email protected]. For

information regarding Authorized Resellers worldwide visit www.srsmith.com

«
...
16
17
18
19
20
...
»

Содержание MultiLift































Отзывы:

Нет отзывов