Ryobi RPD18, Оригинальное руководство пользователя

Страница: 3 / 84

3
Original Instructions
Safety, performance, and dependability have been given top
priority in the design of your percussion drill.
INTENDED USE
The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual, and can be considered responsible
for their actions.
The product is intended for drilling into various materials,
including wood, metal, and plastics using a drill bit having
a shank diameter of less than
13 mm. The product can
be used to drive and remove screws and bolts using an
appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
SURGXFWIRURSHUDWLRQVGLႇHUHQWIURPLQWHQGHGFRXOGUHVXOWLQ
a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool.
Failure to follow all instructions listed below may result
LQHOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Ŷ
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Ŷ
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL
BITS
Ŷ
Never operate at higher speed than the maximum
speed rating of the drill bit.
At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
WKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\
Ŷ
Always start drilling at low speed and with the bit
tip in contact with the workpiece.
At higher speeds,
the bit is likely to bend if allowed to rotate freely without
FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\
Ŷ
Apply pressure only in direct line with the bit and do
not apply excessive pressure.
Bits can bend causing
EUHDNDJHRUORVVRIFRQWUROUHVXOWLQJLQSHUVRQDOLQMXU\
ADDITIONAL SAFETY WARNINGS
Ŷ
Clamp workpiece with a clamping device. Unclamped
ZRUNSLHFHVFDQFDXVHVHYHUHLQMXU\DQGGDPDJH
Ŷ
Dust created by operating the product can cause
UHVSLUDWRU\ LQMXU\ :HDU DSSURSULDWH GXVW FRQWURO PDVN
with filters suitable for protecting against particles from
the material being worked on.
Ŷ ,QMXULHV PD\ EH FDXVHG RU DJJUDYDWHG E\ SURORQJHG
XVHRIDWRRO:KHQXVLQJDQ\WRROIRUSURORQJHGSHULRGV
ensure you take regular breaks.
Ŷ
Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded
Ŷ
Ambient temperature range for tool during operation is
between
0
Û&DQG
40
Û&
Ŷ
Ambient temperature range for tool storage is between
0
Û&DQG
40
Û&
Ŷ
The recommended ambient temperature range for the
charging system during charging is between
10
Û&DQG
38
Û&
ADDITIONAL BATTERY SAFETY WARNINGS
Ŷ 7R UHGXFH WKH ULVN RI ILUH SHUVRQDO LQMXU\ DQG SURGXFW
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
Ŷ
Ambient temperature range for battery during use is
between
0
Û&DQG
40
Û&
Ŷ
Ambient temperature ran
Ŷ
ge for battery storage is between 0
Û&DQG
20
Û&
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 57.
1. Gear selector
2.
7RUTXHDGMXVWPHQWULQJ
3. Keyless chuck
4. Direction of rotation selector
5. Variable speed trigger
6. Handle, insulated gripping surface
7. LED light
8. Battery port
9. Screw driver bit
10. Operator’s manual
11. Drill bit
12. Drill bit
13. Battery pack
14. Charger
ENGLISH
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL