6
WARNING
Ensure that the pressure supplied by the compressed
air system does not exceed the maximum allowable
pressure of the fastener driving tool. Set the air
pressure initially to the lower value of the recommended
DOORZDEOHSUHVVXUHVHH6SHFL¿FDWLRQV
WARNING
Empty the magazine to prevent a fastener from being
ejected at the next stage of work in the event that
internal parts of the fastener driving tool are not in the
starting position following maintenance and repair work
or transportation.
WARNING
Connect the fastener driving tool to the compressed
air supply using suitable pressure hose equipped with
quick-action connectors.
WARNING
Check for proper functioning by applying the safety yoke
of the fastener driving tool to a piece of wood or wooden
material and actuating the trigger once or twice.
This tool is designed to operate on clean, dry compressed
air at regulated pressures between 5.5 - 8.3 bar (80 - 120
psi). The correct air pressure is the lowest pressure that
will do the job.
NOTE:
Air pressure that is higher than 8.3 bar (120 psi)
may damage the tool.
The tool and air hose must have a hose coupling that
allows all pressure to be removed from the tool when the
coupling is disconnected.
WARNING
Always use a coupling that discharges all the
FRPSUHVVHG DLU LQ WKH WRRO DW WKH WLPH WKH ¿WWLQJ RU
hose coupling is disconnected. Using a coupling that
does not discharge the compressed air could cause
unintended operation and serious personal injury.
WARNING
Do not climb rigging or scaffolding while carrying a tool
that is connected to an air hose. Doing so could result
in serious personal injury.
Connect the tool to the air supply with a 1/4 in. female
quick connector. For maximum tool performance, a 3/8 in.
VXSSO\OLQHDQG¿WWLQJVDUHUHTXLUHG
LOADING THE TOOL WITH FASTENERS
6HH¿JXUH
WARNING
2QO\ WKRVH IDVWHQHUV VSHFL¿HG XQGHU 6SHFL¿FDWLRQV
PD\ EH XVHG :KHQ ¿OOLQJ WKH PDJD]LQH KROG WKH
tool so that the safety yoke is not pointing towards the
operator or any other person or animals.
WARNING
The tool’s driving mechanism may cycle when the tool
LV¿UVWFRQQHFWHGWRWKHDLUVXSSO\$OZD\VFRQQHFWWKH
tool to a pressurized air supply before loading fasteners
to prevent injury from unintended cycling. Always make
sure the tool’s magazine is empty at the beginning of
each work session, before connecting to an air supply.
1. Connect the tool to the air supply.
2. Press down on the feeder cover latch and open the
feeder cover. Then open the magazine cover.
3. Adjust the position of spool for the nail size you are
using. The nail will not feed smoothly if the spool is
not correctly adjusted. Refer to "Adjusting the spool"
section for instructions.
4. Slide the coil of nails onto the spool with the nail
pointing down. Uncoil about 7 cm of nails from the coil
of framing nails.
5. Close the magazine. The feeder cover should remain
open.
WARNING
Keep the tool pointed away from yourself and others
when loading fasteners. Failure to do so could result in
possible serious personal injury.
6.
,QVHUWWKH¿UVWQDLOLQWRWKHQDLOFKDPEHU7KH¿UVWQDLO
should sit in the nose of the tool.
7. Position the second nail between the guides. The nail
heads should lie in the track.
8. Securely close the feeder cover, snapping it into
place. Be sure that the feeder cover is locked before
resuming operation.
WARNING
Use only the fasteners recommended for use with this
tool. The use of any other fasteners can result in tool
malfunction, leading to serious injuries.
WARNING
Never load fasteners with the safety yoke or trigger
activated. Doing so could result in possible serious
personal injury.
