Ryobi CHD-1201, Руководство пользователя

Страница: 12 / 116

8
English
GB
D E I P NL S DK N GR H CZ RUS RO FIN FR SLO HR TR PL
CHARGER SAFETY
■
Do not operate charger with a damaged cord or
plug. If damaged, have it replaced immediately by a
qualified serviceman.
■
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman.
■
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock or fire.
■
To reduce risk of electric shock, unplug the charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this risk.
■
Disconnect charger from power supply when not in use.
■
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
■
Save these instructions. Refer to them frequently and
use them to instruct others who may use this unit.
If you loan someone this unit, loan them these
instructions also.
DESCRIPTION
See Figure 1-6
1. Keyless chuck
2. Switch trigger
3. Direction of rotation selector (Forward/Reverse)
4. Screwdriver bits
5 . Battery pack
6. Latches
7. Depress latches to release battery pack
8. To Decrease torque
9. To Increase torque
10. Torque adjusting Ring
11. Reverse
12. Forward
13. Drill bit (Not Included)
14. Chuck jaws
15. Unlock(release)
16. Lock (tighten)
17. Battery Charger
18. LED indicator
19. LED worklight
OPERATION
CHARGING YOUR BATTERY PACK
See Figure 6.
The battery pack for your tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
Note: Batteries will not reach full charge the first time
they are charged. Allow several cycles for them to
fully charge.
TO CHARGE
■
Charge battery pack only with the charger provided.
■
Make sure power supply is normal house voltage, 230
volts, 50 Hz, AC only.
■
Connect charger to power supply.
■
Make sure charger plug and input jack are properly
connected.
■
Place battery pack in charger. Align raised rib on
battery pack with groove in charger.
■
Press down on battery pack to be sure contacts
on battery pack engage properly with contacts in
charger. When properly connected, red light will turn
on.
■
The LED indicator, which is located on the charging
stand, will light up when charger is properly
connected to power supply. This light indicates your
tool is charging and will remain on until charger is
disconnected from power supply.
■
After normal usage, 3-5 hours of charge time are
required to be fully charged. A minimum charge
time of 5 hours is required to recharge a completely
discharged tool.
■
DO NOT place charger in an area of extreme heat
or cold. It will work best at temperatures above 10°C
and below 38°C
IMPORTANT INFORMATION FOR RECHARGING HOT
BATTERIES
When using your tool continuously, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
TO INSTALL BATTERY PACK
■
Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 4.
■
Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill.
See Figure 2.
■
Make sure the latches on battery pack snap in place
and battery pack is secured in drill before beginning
operation.
8
960931153-01(print).indd 8 960931153-01(print).indd 8 7/18/07 11:27:35 AM 7/18/07 11:27:35 AM