background image

9. Place the spring in the inner reel. Insert the

ends of the line through the eyelets in the
outer spool and place inner reel inside the
outer spool (Fig. 35). Push the inner reel and
outer spool together. While holding the inner
reel and outer spool, grasp the ends and pull
firmly to release the line from the holding
slots in the spool.

NOTE:

The spring must be assembled on 
the inner reel before reassembling 
the cutting attachment.

MAINTENANCE AND REPAIR INSTRUCTIONS

22

7. Wind the lines in tight even layers, onto the

reel (Fig. 33). Wind the line in the direction
indicated on the inner reel. Place your index
finger between the two lines to stop the lines
from overlapping. Do not overlap the ends 
of the line. 

NOTE:

Failure to wind the line in the direction
indicated will cause the cutting
attachment to operate incorrectly.

8. Insert the ends of the line into the two

holding slots (Fig. 34).

Fig. 33

Fig. 34

Fig. 35

Fig. 32

6. Take approximately 25 feet (7.6 m) of new

trimming line, loop it into two equal lengths.
Insert each end of the line through one of the
two holes in the inner reel (Fig. 32). Pull the
line through the inner reel so that the loop is
as small as possible.

NOTE:

Always use the correct line length
when installing trimming line on the
unit. The line may not release properly
if the line is too long.

10.Hold the inner reel in place and install the

Bump Knob™ by turning counterclockwise.
Tighten securely.

Holding Slots

Содержание 780r

































Отзывы: