Ryobi 767r Скачать руководство пользователя | Manualshive

Страница: 7 / 28

background image

RULES FOR SAFE OPERATION

7

• THROWN OBJECTS AND ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING:

Do not operate without the cutting attachment

shield in place. Keep away from the rotating cutting
attachment.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF OR STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or cylinder. You may get burned.
These parts get extremely hot from operation. When turned
off they remain hot for a short time.

• SHARP BLADE

WARNING:

There is a sharp blade on the cutting attachment

shield. To prevent serious injury, do not touch blade.

SYMBOL

MEANING

• CHOKE CONTROL

A

•

FULL CHOKE

position.

B

•

PARTIAL CHOKE

position.

C

•

RUN

position.

• INDICATES OIL

Refer to operator's manual for the proper type of oil.

• DO NOT USE BLADES

WARNING:

To prevent serious injury, do not attach or operate

the unit with any type of blade.

WARNING:

The operation of any power tool can cause foreign objects to be

thrown into your eyes. This can lead to severe eye damage. Before commencing
power tool operation, always wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards, and a full face shield when needed.

«
...
5
6
7
8
9
...
»

Содержание 767r





























Отзывы:

Нет отзывов

Похожие инструкции для 767r

Бренд: Yard-Man Страницы: 12

Бренд: Gardenline Страницы: 12

Бренд: Oh!FX Страницы: 4

Flex-Force Power System 51841

Бренд: Toro Страницы: 48

Бренд: Morrison Страницы: 8

Бренд: Garland Страницы: 148

Бренд: Tanaka Страницы: 24

Бренд: YATO Страницы: 73

Бренд: Echo Страницы: 28

Бренд: Makita Страницы: 92

Бренд: FLORABEST Страницы: 152

Sunjoe 20ViONLTE-PHT17-RM

Бренд: SNOWJOE Страницы: 20

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 44

Бренд: Echo Страницы: 52

Бренд: Beper Страницы: 40

Бренд: McCulloch Страницы: 64

Бренд: Talon Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды