background image

RYOBI OUTDOOR PRODUCTS warrants each new
RYOBI Product for two (2) years according to the
following terms.

This warranty extends to the original retail purchaser
only and commences on the date of original retail
purchase.

Any part of the RYOBI Product manufactured or
supplied by RYOBI and found in the reasonable
judgement of RYOBI to be defective in material or
workmanship will be repaired or replaced by an
authorized RYOBI service dealer without charge 
for parts and labor.

The RYOBI Product including any defective part 
must be returned to an authorized service dealer
within the warranty period. The expense of delivering
the RYOBI Product to the dealer for warranty work
and the expense of returning it back to the owner
after repair or replacement will be paid for by the
owner. RYOBI’s responsibility in respect to claims is
limited to making the required repairs or replacements
and no claim of breach of warranty shall be cause 
for cancellation or rescission of the contract of sale 
of any RYOBI Product. Proof of purchase will be
required by the dealer to substantiate any warranty
claim. All warranty work must be performed by an 
authorized RYOBI service dealer.

This warranty is limited to ninety (90) days from 
the date of original retail purchase for any RYOBI
Product that is used for rental or commercial
purposes, or any other income-producing purpose.

This warranty does not cover any RYOBI Product 
that has been subject to misuse, neglect, negligence,
or accident, or that has been operated in any way
contrary to the operating instructions as specified in
the RYOBI Operator’s Manual. This warranty does not
apply to any damage to the RYOBI Product that is the
result of improper maintenance or to any RYOBI
Product that has been altered or modified so as to
adversely affect the product's operation, performance
or durability or that has been altered or modified so
as to change its intended use. The warranty does not
extend to repairs made necessary by normal wear or
by the use of parts or accessories which are either
incompatible with the RYOBI Product or adversely
affect its operation, performance or durability.

In addition, this warranty does not cover:
A. Tune-ups - Spark Plugs, Carburetor 

Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools,

Cutting Line, Inner Reels, Starter Pulley,
Starter Ropes, Drive Belts

RYOBI reserves the right to change or improve the
design of any RYOBI Product without assuming any
obligation to modify any product previously
manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE TWO (2) YEAR WARRANTY
PERIOD OR NINETY (90) DAYS FOR PRODUCTS
USED FOR ANY COMMERCIAL PURPOSE.
ACCORDINGLY, ANY SUCH IMPLIED
WARRANTIES INCLUDING MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE, ARE DISCLAIMED IN THEIR
ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR OR NINETY DAY
WARRANTY PERIOD. RYOBI’S OBLIGATION
UNDER THIS WARRANTY, IS STRICTLY AND
EXCLUSIVELY LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS, AND ROP
DOES NOT ASSUME OR AUTHORIZE
ANYONE TO ASSUME FOR THEM ANY OTHER
OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.

RYOBI ASSUMES NO RESPONSIBILITY FOR
INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED
TO EXPENSE OF RETURNING THE RYOBI
PRODUCT TO AN AUTHORIZED SERVICE
DEALER AND EXPENSE OF DELIVERING IT BACK
TO THE OWNER, MECHANIC’S TRAVEL TIME,
TELEPHONE OR TELEGRAM CHARGES, RENTAL
OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED,
TRAVEL, LOSS OR DAMAGE TO PERSONAL
PROPERTY, LOSS OF REVENUE, LOSS OF USE OF
THE PRODUCT, LOSS OF TIME, OR
INCONVENIENCE. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU.

This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state.

This warranty applies to all RYOBI Products
manufactured by RYOBI and sold in the United
States and Canada.

To locate your nearest service dealer dial
1-800-345-8746 in the United States or
1-800-265-6778 in Canada.

RYOBI OUTDOOR PRODUCTS

550 N. 54th Street

Chandler, AZ 85226 U.S.A.

RYOBI CANADA INC.

275 Industrial Rd

Cambridge, Ontario N1R 6K2 CANADA

LIMITED TWO-YEAR WARRANTY

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR QUESTIONS CALL 1-800-345-8746 IN U.S.

OR 1-800-265-6778 IN CANADA

OPERATOR’S MANUAL PART NO. 182085

REV. B (7675)

PRINTED IN U.S.A

10/98

Содержание 767r





























Отзывы: