Ryobi 767r Скачать руководство пользователя | Manualshive

Страница: 6 / 28

background image

RULES FOR SAFE OPERATION

6

OTHER SAFETY WARNINGS

•

Never store the unit, with fuel in the tank,
inside a building where fumes may reach an
open flame or spark.

•

Allow the engine to cool before storing or
transporting. Be sure to secure the unit while
transporting.

•

Store the unit in a locked up and dry or high
and dry place to prevent unauthorized use or
damage, out of the reach of children.

•

Never douse or squirt the unit with water or
any other liquid. Keep handles dry, clean and
free from debris. Clean after each use, see

Cleaning and Storage

instructions.

•

Keep these instructions. Refer to them often
and use them to instruct other users. If you
loan someone this unit, also loan them these
instructions.

SAVE THESE INSTRUCTIONS

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear
on this product. Read the operator's manual for complete safety, assembly, operating and
maintenance and repair information.

•

WARNING - READ OPERATOR'S MANUAL

Read the Operator’s Manual(s) and follow all warnings and safety
instructions. Failure to do so can result in serious injury to the
operator and/or bystanders.

MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or caution. May be used in
conjunction with other symbols or pictographs.

• PRIMER BULB

Push primer bulb, fully and slowly, 5 to 7 times.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all bystanders, especially children and pets,

at least 50 feet (15 m.) from the trimming area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• FOR SERVICE INFORMATION, CALL:

USA: 1-800-345-8746
CANADA: 1-800-265-6778

• WEAR EYE AND HEARING PROTECTION

WARNING:

Thrown objects and loud noise can cause severe eye

injury and hearing loss. Wear eye protection meeting ANSI
Z87.1-1989 standards and ear protection when operating this unit.

SYMBOL

«
...
4
5
6
7
8
...
»

Содержание 767r





























Отзывы:

Нет отзывов

Похожие инструкции для 767r

Бренд: Echo Страницы: 28

Flex-Force Power System 51841

Бренд: Toro Страницы: 48

HWT 700 SUPERTRAC

Бренд: Grillo Страницы: 56

Бренд: DeWalt Страницы: 56

Бренд: DeWalt Страницы: 40

Бренд: DeWalt Страницы: 96

Бренд: DeWalt Страницы: 160

Бренд: DeWalt Страницы: 112

Pro Landscaping DCM586

Бренд: DeWalt Страницы: 164

Бренд: DeWalt Страницы: 124

XR LI-ION DCMASST1

Бренд: DeWalt Страницы: 92

PRO LANDSCAPING DCM583N

Бренд: DeWalt Страницы: 140

Бренд: Troy-Bilt Страницы: 28

Бренд: Leviton Страницы: 35

Бренд: ZooZ Страницы: 3

Бренд: McCulloch Страницы: 20

Бренд: Talon Страницы: 3

Бренд: Wahl Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды