Russound CAM6.6X Скачать руководство пользователя страница 54

Страница: 54 / 116

INSTALLER

INSTALLATION MENU

2. BANK NAME –

Use the up/down keys to select a character and left/right keys

(BnkNm)

to change a character position. A blinking cursor indicates the
placement of the character being entered. Names can be from 1
to 12 characters in length.

CONTROLLR ID (CtlId)

This procedure is used to identify the controller(s) that the tuner will respond to.

See Periph Setup

- Flow Chart page 68

1. Controller:# –

Select controller ID of controller that will control tuner.

(CtlId)

2. All controllers –

Select if all controllers in system can control the tuner.

(All)

DIAGNOSTICS (Diags)

This procedure is for factory use only.

See Periph Setup - Flow Chart page 68

FACTORY INIT (FInit)

NOTE: This procedure returns the tuner to its factory settings and erases all user settings.

This procedure allows the erasure of all programmed settings and returns them to the factory default
settings.

See Periph Setup - Flow Chart 68

1. Are you sure? –

Confirmation of YES or NO is required to proceed. A NO

(Sure?)

selection returns to the top of the Factory Initialization menu.
A YES selection begins the initialization.

2. Please Wait –

Message shows during the initialization process.

3. Cycle Power –

When initialization is complete, cycle power to the unit.

SYSTEM INFO (SInfo)

System Info shows the tuner’s manufacturing build properties.

See Periph Setup - Flow Chart 68

BUILD TIME (BTime)

BUILD DATE (BDate)

VERSION (Ver)

Содержание CAM6.6X





















































































































Результаты поиска

Содержание CAM6.6X

Отзывы:

Похожие инструкции для CAM6.6X

Бренды по названию

Популярные бренды

Russound CAM6.6X, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X

Отзывы:

Похожие инструкции для CAM6.6X

Бренды по названию

Популярные бренды