Russound CAM6.6X Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 116

background image

43

The RNET Link In and Link Out is used to con-
nect two or more CAM6.6 or CAV6.6 con-
trollers. The connection is made using a CAT-5
patch cable from the Link Out of the master
CAM6.6 and into the Link In of the next con-
troller. Along with RNET data signals, the RNET
Link In and Link Out jack passes the six source
IR signals. These are only for source-specific IR
remote repeating, not codes initiated from the
controller’s internal IR library. The CAT-5 patch
cable should not exceed 18 inches in length to
avoid potential cross-talk between the source-
specific IR repeating signal lines.

The RNET Link In and Link Out is also used to
connect the CAM6.6 to other Russound prod-
ucts with RNET.

Note: If two or more CAM6.6 or CAV6.6 con-
trollers will be connected using the RNET Link In
and Link Out ports, each controller must have a
unique Controller ID prior to being connected
through the RNET ports. The Controller ID
assignment must be performed during the
Controller Setup section of the Installation menu.

CAM6.6

A

NTENNA

CAV6.6 (Controller ID 2)

CAM6.6 (Controller ID 1)

CA

T-5 C

able (MAX LENGTH 18 inches)

INSTALLER

MAKING CONNECTIONS

RNET Link In and Link Out

«
...
41
42
43
44
45
...
»

Содержание CAM6.6X





















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6X

Бренд: Eclipse Страницы: 86

Бренд: Accurate Technology Страницы: 20

Бренд: Pansat Страницы: 32

Бренд: Teac Страницы: 128

Бренд: Teac Страницы: 56

Бренд: Teac Страницы: 136

Бренд: Teac Страницы: 22

Бренд: Audiovox Страницы: 112

Бренд: Nexa Страницы: 24

Бренд: ADI Страницы: 47

IC-F1000 series

Бренд: Icom Страницы: 2

Бренд: NAL Страницы: 9

Бренд: K1EL Страницы: 53

Бренд: GTX Страницы: 7

Бренд: Arris Страницы: 24

PowerBox Cockpit

Бренд: PowerBox Systems Страницы: 30

Бренд: Yaesu Страницы: 20

Бренд: Audiovox Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды